ARDUINO ABX00031 Nano 33 BLE Sense

Fa'amatalaga

Nano 33 BLE Sense o se la'ititi lapopo'a lapopo'a o lo'o iai le NINA B306 module, fa'avae i luga o le Nordic nRF52480 ma o lo'o i ai se Cortex M4F, o se pusi crypto e mafai ona fa'amautu fa'amaumauga ma ki fa'asoa muamua ma le 9 axis IMU. O le module e mafai ona faʻapipiʻiina e avea o se vaega DIP (pe a faʻapipiʻi ulutala pine), poʻo se vaega SMT, faʻapipiʻi saʻo e ala i pads castellated.
Itulau fa'atatau:
Fausia, faʻaleleia, faʻaoga IoT

Vaega

• NINA B306 Module
• Processor
• 64 MHz Arm® Cortex-M4F (faatasi ai ma le FPU) 1
• MB Flash + 256 KB RAM

Bluetooth 5 multiprotocol leitio

• 2 Mbps
• CSA #2
• Fa'aopoopo Fa'asalalauga
• Va'aiga Umi
• +8 dBm TX mana
• -95 dBm lagona
• 4.8 mA i le TX (0 dBm)
• 4.6 mA i le RX (1 Mbps)
• Balun tu'ufa'atasi ma le 50 Ω fa'ai'uga ta'itasi IEEE 802.15.4 lagolago leitio
• filo
• Zigbee

Peripherals

• Saosaoa atoatoa 12 Mbps USB
• NFC-A tag
• Arm CryptoCell CC310 subsystem puipuiga malu QSPI/SPI/TWI/I²S/PDM/QDEC
• Saosaoa maualuga 32 MHz SPI
• Quad SPI fa'aoga 32 MHz
• EasyDMA mo feso'ota'iga numera uma
• 12-bit 200 ksps ADC
• 128 bit AES/ECB/CCM/AAR co-processor

LSM9DS1 (9 axis IMU)

• 3 auala fa'avavevave,
• 3 alavai fua fa'atatau,
• 3 alavai maneta ±2/±4/±8/±16 g
• fa'atelega fa'avavevave
• ±4/±8/±12/±16 gauss maneta fua atoa
• ± 245 / ± 500 / ± 2000 dps fua fa'atatau fua fa'atatau atoa
• 16-bit fa'amatalaga fa'amatalaga

LPS22HB (Barometer ma le vevela)

• 260 i le 1260 hPa le maualuga o le mamafa ma le 24 bit saʻo
• Malosi maualuga ova malosi: 20x fa'afuafua atoa
• Taui o le vevela fa'apipi'i
• 16-bit fa'amaumauga o le vevela
• 1 Hz i le 75 Hz fua faatatau o fa'amatalaga fa'alavelave Fa'alavelave:
• Sauni Fa'amatalaga, fu'a FIFO, tulaga fa'aoso

HTS221 (se'i susū)

• 0-100% va'aiga susū fa'atatau
• Ma'ale'ale RH maualuga: 0.004% rH/LSB
• Sa'o le susu: ± 3.5% rH, 20 i le + 80% rH
• Sa'o le vevela: ± 0.5 °C,15 i le +40 °C 16-bit
• fa'amaumauga o le susū ma le vevela

APDS-9960 (Digital praoximity, Ambient light, RGB and Gesture Sensor)

• Ambient Light ma RGB
• Fa'alogoina Lanu ma le UV ma le IR
• poloka poloka Ma'ale'ale maualuga tele – E fetaui lelei mo le fa'agaioiga i tua o tioata pogisa
• Latalata Lagona fa'atasi ai ma le fa'ate'aina o le malamalama Ambient
• Lavelave Gaioiga Lagona

MP34DT05 (Ma'i leo leo)

• AOP = 122.5 dbSPL
• 64 dB fua faatatau fa'ailo i le pisa
• Omnidirectional maaleale –26 dBFS ± 3
• dB lagona

ATECC608A (Crypto Chip)

• Cryptographic co-processor fa'atasi ai ma le teuina o ki fa'avae fa'amautu
• Puipuia le teuina e oo atu i le 16 ki, tusipasi po'o fa'amaumauga
• ECDH: FIPS SP800-56A Elliptic Curve Diffie-Hellman
• NIST tulaga masani P256 elliptic curve lagolago
• SHA-256 & HMAC hash e aofia ai le fa'asa'o/toe fa'afo'i fa'ailoga AES-128,
• fa'ato'a fa'ateleina le fanua galois mo le GCM

MPM3610 DC-DC
Fa'atonutonu mea e tu'uina atu voltagu mai luga i le 21V ma le itiiti ifo i le 65% lelei le uta aupito maualalo Sili atu i le 85% lelei 12V

Le Komiti Faatino

E pei o laupapa uma o le Nano form factor, Nano 33 BLE Sense e leai se uta maa ae e mafai ona fa'aola ile USB po'o ulutala.
FAAMANATU: Arduino Nano 33 BLE Sense e na'o le lagolagoina o le 3.3VI/Os ma e LĒ 5V fa'apalepale fa'amolemole ia mautinoa e te le o fa'afeso'ota'i sa'o fa'ailo 5V i lenei laupapa pe o le a fa'aleagaina. E le gata i lea, e ese mai i laupapa Arduino Nano e lagolagoina le 5V galuega, o le 5V pine e LE maua ai vol.tage ae e sili atu ona fesoʻotaʻi, e ala i se osooso, i le USB power input.
 Fa'ailoga
Tulaga Fautuaina o Galuega

Faailoga	Fa'amatalaga	Min	Max
	Tapula'a fa'amama fa'asao mo le laupapa atoa:	-40 °C (40 °F)	85°C (185°F)

Fa'aaogāga Malosiaga

Faailoga	Fa'amatalaga	Min	Ituaiga	Max	Vaega
PBL	Malosiaga fa'aaoga ma pisi pisi		TBC		mW
PLP	Le fa'aogaina o le malosi ile tulaga maualalo ole mana		TBC		mW
PMAX	Fa'aaogāina Malosi maualuga		TBC		mW

 Faagaioia i Lugaview
 Laupapa Topology
Luga:

Ref.	Fa'amatalaga	Ref.	Fa'amatalaga
U1	NINA-B306 Module BLE 5.0 Module	U6	MP2322GQH Step Down Converter
U2	LSM9DS1TR Sensor IMU	PB1	IT-1185AP1C-160G-GTR Pusa faamau
U3	MP34DT06JTR Mems Microphone	HS-1	HTS221 Sūsū Sensori
U4	ATECC608A Crypto chip	DL1	Led L
U5	APDS-9660 Ambient Module	DL2	Ta'ita'i Mana

Ref.	Fa'amatalaga	Ref.	Fa'amatalaga
SJ1	VUSB Jumper	SJ2	D7 Tagata osooso
SJ3	3v3 Fa'aoso	SJ4	D8 Tagata osooso

Processor
O le Processor Autu o se Cortex M4F e oʻo atu i le 64MHz. O le tele o ona pine e feso'ota'i i ulutala i fafo, peita'i o nisi o lo'o fa'aagaga mo feso'ota'iga i totonu ma le module uaealesi ma le I2C peripherals i totonu (IMU ma Crypto).
FAAMANATU:
E ese mai i isi laupapa Arduino Nano, o pine A4 ma le A5 o loʻo i ai se toso i luga ma e le mafai ona faʻaaogaina o se I2C Bus ona e le fautuaina le faʻaogaina o mea faʻaoga analog.

 Crypto
O le crypto chip i Arduino IoT boards o le mea lea e fai ai le eseesega ma isi laupapa e le malu puipuia ona e maua ai se auala saogalemu e teu ai mealilo (pei o tusipasi) ma faʻavavevave faʻamautu faʻamaonia ae le faʻaalia mea lilo i tusitusiga manino. Source code mo le Arduino Library e lagolagoina le Crypto o loʻo avanoa [8]

IMU
Arduino Nano 33 BLE o loʻo i ai se 9 axis IMU faʻapipiʻi lea e mafai ona faʻaaogaina e fua ai le faʻatonuga o le laupapa (e ala i le siakiina o le kalave faʻavavevave vector orientation poʻo le faʻaaogaina o le tapasa 3D) poʻo le fuaina o teteʻi, vibration, faʻavavevave ma le saoasaoa o le suiga. Source code mo le Arduino O lo'o avanoa le faletusi e lagolagoina le IMU [9]

Barometer ma le Temperature Sensor
O le Barometer fa'apipi'i ma le masini vevela e mafai ai ona fua le mamafa o le ambient. E mafai ona fa'aoga le masini vevela fa'atasi ma le barometer e totogi ai le fua o le mamafa.
O loʻo maua le code source mo le Arduino Library e lagolagoina le Barometer [10]

 Susū Fete'ena'i ma le Su'esu'e o le vevela
Su'e susū fa'atatau e fua ai le susū fa'atasi. E pei o le Barometer o lenei masini e iai se masini vevela tuʻufaʻatasia e mafai ona faʻaaoga e totogi ai le fua.
O loʻo maua le code source mo le Arduino Library o loʻo lagolagoina le masini Susū [11]

Fa'afuainumera Latalata, Ambient Light, RGB ma Gasture Sensor
O lo'o maua le fa'ailoga puna mo le Arduino Library e lagolagoina le Proximity/gesture/ALS sensor [12]

 Su'eina Gaioiga
O le su'esu'eina o taga e fa'aogaina ai ata fa'ata'ita'i e fa e lagona ai le fa'aalia o le malosi o le IR (na maua mai i le LED tu'ufa'atasi) e fa'aliliu ai le tino.

Su'esu'ega Latalata
O le mea e iloa ai le Proximity e maua ai le fuaina o le mamao (Fa'ata'ita'iga o masini feavea'i mata i le taliga o le tagata fa'aoga) e ala i le photodiode su'esu'ega o fa'ata.

Lanu ma le Su'esu'ega ALS
Ole mea e iloa ai le Lanu ma le ALS e maua ai fa'amatalaga mumu, lanumeamata, lanumoana ma manino le malamalama. O laina taʻitasi R, G, B, C e iai le UV

Faʻalogo leo puʻeata
O le MP34DT05 o se ultra-compact, low-power, omnidirectional, digital MEMS microphone ua fausia ma se elemene sensing capacitive ma se IC interface.O le elemene sensing, e mafai ona iloa ai galu acoustic, ua gaosia e faʻaaoga ai se faiga faʻapitoa silicon micromachining faʻapitoa e gaosia ai leo. fa'alogo

Laau Malosi
E mafai ona fa'aola le laupapa e ala i feso'ota'iga USB, VIN po'o VUSB pine i luga o ulutala.

FAAMANATU:
Talu ai ona o le VUSB e fafaga le VIN e ala i le Schottky diode ma le DC-DC regulator ua faʻamaonia le pito maualalo o le voli ulufale.tage 4.5V le pito maualalo voltage mai le USB e tatau ona fa'aopoopo i le voltage i le va o le 4.8V i le 4.96V e faʻatatau i le taimi nei o loʻo tusia.

 Galuega a le Komiti Faatino

Amataina - IDE
Afai e te mana'o e fa'apolokalame lau Arduino Nano 33 BLE a'o to'aga e te mana'omia fa'apipi'i le Arduino Desktop IDE [1] Ina ia fa'afeso'ota'i le Arduino Nano 33 BLE i lau komepiuta, e te mana'omia se uaea Micro-B USB. E maua ai foi le malosiaga i le laupapa, e pei ona faʻaalia e le LED.

 Amataina - Arduino Web Fa'atonu
O laupapa Arduino uma, e aofia ai ma lenei, galue i fafo-o-le-pusa i luga o le Arduino Web Fa'atonu [2], i le na'o le fa'apipi'iina o se mea fa'apipi'i faigofie.
Le Arduino Web Fa'atonu e talimalo i luga o le initaneti, o le mea lea o le a fa'afou i taimi uma ma foliga fou ma lagolago mo laupapa uma. Mulimuli i le [3] e amata fa'ailoga i luga ole su'esu'ega ma fa'ae'e au ata tusi ile lau laupapa.

Amataina - Arduino IoT Cloud
O oloa uma Arduino IoT e mafai ona lagolagoina i Arduino IoT Cloud lea e mafai ai e oe ona Log, kalafi ma auʻiliʻili faʻamatalaga faʻamatalaga, faʻaosoina mea tutupu, ma faʻaogaina lou fale poʻo pisinisi.

Sample Tusitusi
SampO ata tusi mo le Arduino Nano 33 BLE e mafai ona maua i le "Examples" lisi i le Arduino IDE poʻo le vaega "Documentation" o le Arduino Pro webnofoaga [4]

 Punaoa i luga ole laiga
I le taimi nei ua uma ona e pasia faʻavae o mea e mafai ona e faia i le laupapa e mafai ona e suʻesuʻeina avanoa e le gata e maua mai e ala i le siakiina o galuega faʻafiafia i ProjectHub [13], le Arduino Library Reference [14] ma le faleoloa i luga ole laiga [15] lea. o le a mafai ona e fa'amae'a lau laupapa i masini, actuators ma sili atu.

 Toe fa'aleleia a le Komiti Fa'atonu
O laupapa Arduino uma o loʻo i ai se faʻapipiʻi faʻapipiʻiina e mafai ai ona faʻafefeina le laupapa e ala i le USB. Afai e loka e se ata tusi le faagasologa ma ua le toe mafai ona oo atu i ai le laupapa e ala i le USB e mafai ona ulufale i le bootloader mode e ala i le ta faaluaina le faamau toe setiina pe a uma le eletise.

 Fesootaiga Pinout

USB

Pin	Galuega	Ituaiga	Fa'amatalaga
1	VUSB	Malosiaga	Malosiaga Tuuina atu. Afai e fa'aola le laupapa e ala i le VUSB mai le fa'auluuluga o le mea lea (1)
2	D-	Eseesega	USB faʻamatalaga faʻapitoa -
3	D+	Eseesega	USB fa'amatalaga eseese +
4	ID	fa'atusa	Filifilia le fa'aogaina o le Host/Device
5	GND	Malosiaga	Eleele Eleele

Ulutala
O lo'o fa'aalia e le laupapa ni feso'ota'iga 15 pine e lua e mafai ona fa'apipi'i fa'atasi ma fa'aulu fa'aulu pe fa'asoloina e ala i vias fa'apipi'i.

Pin	Galuega	Ituaiga	Fa'amatalaga
1	D13	Faafuainumera	GPIO
2	+3V3	Malosiaga	Fa'alotoifale fa'aola le mana fa'aola i masini fafo
3	AREF	fa'atusa	Analog Reference; e mafai ona faʻaaogaina e avea ma GPIO
4	A0/DAC0	fa'atusa	ADC i totonu/DAC fafo; e mafai ona faʻaaogaina e avea ma GPIO
5	A1	fa'atusa	ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO
6	A2	fa'atusa	ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO
7	A3	fa'atusa	ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO
8	A4/SDA	fa'atusa	ADC i totonu; I2C SDA; E mafai ona faʻaaogaina e avea ma GPIO (1)
9	A5/SCL	fa'atusa	ADC i totonu; I2C SCL; E mafai ona faʻaaogaina e avea ma GPIO (1)
10	A6	fa'atusa	ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO
11	A7	fa'atusa	ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO
12	VUSB	Malosiaga i totonu/Ofo	E masani lava NC; e mafai ona faʻafesoʻotaʻi i le VUSB pine o le USB connector e ala i le faʻapuupuuina o se osooso
13	RST	Digital In	Malosiaga toe setiina fa'aoga (faiga o pine 18)
14	GND	Malosiaga	Eleele Eleele
15	VIN	Malosiaga i totonu	Vin Malosiaga ulufale
16	TX	Faafuainumera	USART TX; e mafai ona faʻaaogaina e avea ma GPIO
17	RX	Faafuainumera	USART RX; e mafai ona faʻaaogaina e avea ma GPIO
18	RST	Faafuainumera	Malosiaga toe setiina fa'aoga (faiga o pine 13)
19	GND	Malosiaga	Eleele Eleele
20	D2	Faafuainumera	GPIO
21	D3/PWM	Faafuainumera	GPIO; e mafai ona faʻaaogaina e fai ma PWM
22	D4	Faafuainumera	GPIO
23	D5/PWM	Faafuainumera	GPIO; e mafai ona faʻaaogaina e fai ma PWM
24	D6/PWM	Faafuainumera	GPIO, e mafai ona faʻaaogaina e fai ma PWM
25	D7	Faafuainumera	GPIO
26	D8	Faafuainumera	GPIO
27	D9/PWM	Faafuainumera	GPIO; e mafai ona faʻaaogaina e fai ma PWM
28	D10/PWM	Faafuainumera	GPIO; e mafai ona faʻaaogaina e fai ma PWM
29	D11/MOSI	Faafuainumera	SPI MOSI; e mafai ona faʻaaogaina e avea ma GPIO
30	D12/MISO	Faafuainumera	SPI MISO; e mafai ona faʻaaogaina e avea ma GPIO

Debug
I le pito i lalo o le laupapa, i lalo o le module fesoʻotaʻiga, o faʻailoga debug o loʻo faʻatulagaina e pei o 3 × 2 pads suʻega ma 100 mil pitch ma pine 4 aveese. O le pine 1 o loʻo faʻaalia i le Ata 3 - Tulaga Fesoʻotaʻi

Pin	Galuega	Ituaiga	Fa'amatalaga
1	+3V3	Malosiaga	Malosiaga e gaosia i totonu e fa'aaogaina e pei o voltagu faasinomaga
2	SWD	Faafuainumera	nRF52480 Fa'amatalaga Debug Uea Tasi
3	SWCLK	Digital In	nRF52480 Uaea Tasi Debug Uati
5	GND	Malosiaga	Eleele Eleele
6	RST	Digital In	Malosiaga maualalo toe seti fa'aoga

Fa'amatalaga Fa'ainisinia

Otootoga o le Laupapa ma Pu Fa'amau
O fua fa'atonu e fefiloi i le va o le metric ma le imperial. E fa'aogaina faiga fa'a-Imperial e fa'amautu ai le 100 mil pitch grid i le va o laina pine e fa'ataga ai latou e fa'apipi'i se laupapa falaoa ae o le umi o le laupapa o le Metric.

Tusipasi

Ta'utinoga o le tausisia CE DoC (EU)
Matou te taʻutino atu i lalo o la matou matafaioi e faʻapea o oloa o loʻo i luga o loʻo ogatasi ma manaʻoga taua o taʻiala a le EU o loʻo mulimuli mai ma o lea e agavaʻa ai mo feoaiga saoloto i totonu o maketi e aofia ai le Iuni a Europa (EU) ma Europa Economic Area (EEA).

 Ta'utinoga o le tausisia i le EU RoHS & REACH 211 01/19/2021
O laupapa Arduino o loʻo tausisia le RoHS 2 Directive 2011/65/EU o le Palemene Europa ma le RoHS 3 Directive 2015/863/EU o le Fono a Iuni 4 Iuni 2015 i le faʻatapulaʻaina o le faʻaaogaina o nisi mea matautia i mea eletise ma eletise.

Mea	tapulaa maualuga (ppm)
Sulu (Pb)	1000
Cadmium (Cd)	100
Mercury (Hg)	1000
Hexavalent Chromium (Cr6+)	1000
Poly Brominated Biphenyl (PBB)	1000
Poly Brominated Diphenyl ethers (PBDE)	1000
Pi(2-Ethylhexyl} phthalate (DEHP)	1000
Benzyl butyl phthalate (BBP)	1000
Dibutyl phthalate (DBP)	1000
Diisobutyl phthalate (DIBP)	1000

Tuusaunoaga: E leai ni tuusaunoaga e talosagaina.
Arduino Boards o lo'o tausisia atoatoa mana'oga fa'atatau i le Tulafono Fa'atonutonu a Iuni a Europa (EC) 1907/2006 e uiga i le Fa'amauina, Iloiloga, Fa'atagaga ma Fa'asaina o Vailaau Fa'asaina (REACH). Matou te taʻutino atu e leai se SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), o le Lisi o Sui Tofia o mea e sili ona popole mo le faʻatagaga o loʻo tuʻuina atu nei e le ECHA, o loʻo i ai i oloa uma (ma faʻapea foʻi afifi) i le aofaʻi atoa i se faʻatonuga tutusa pe sili atu i le 0.1%. I le mea sili o lo matou iloa, matou te tautino atu foi oa matou oloa e le o iai ni mea o loʻo lisiina i luga o le "Lisi Faʻatagaina" (Faʻaopoopoga XIV o tulafono a le REACH) ma mea o loʻo popole tele (SVHC) i soʻo se aofaiga tele e pei ona faʻamaonia. e le Annex XVII o le Lisi o Sui Fa'asalalau na lomia e le ECHA (European Chemical Agency) 1907

Ta'utinoga o Minerale Fete'ena'i
I le avea ai o se tagata e tu'uina atu vaega fa'aeletoroni ma eletise i le lalolagi atoa, o lo'o nofouta Arduino i a tatou matafaioi e tusa ai ma tulafono ma tulafono fa'atatau i Fete'ena'iga Minerale, fa'apitoa le Dodd-Frank Wall Street Reform and Consumer Protection Act, Vaega 1502. minerale pei ole Tin, Tantalum, Tungsten, poʻo le Auro. O minerale fete'ena'i o lo'o i totonu oa tatou oloa i le tulaga o le solder, po'o se vaega i u'amea u'amea. O se vaega o la matou su'esu'ega talafeagai ua fa'afeso'ota'i ai e Arduino vaega fa'atau oloa i totonu o la matou sapalai filifili e fa'amaonia lo latou tausisia pea o tulafono faatonutonu. E tusa ai ma fa'amatalaga ua maua e o'o mai i le taimi nei, matou te ta'utino atu o a matou oloa o lo'o iai Minerale Fete'ena'i e maua mai i nofoaga e leai ni fete'ena'iga.

 FCC Lapataiga

So'o se Suiga po'o ni suiga e le'i fa'amaonia manino e le itu e nafa ma le usita'ia e mafai ona fa'aleaogaina le pule a le tagata fa'aoga e fa'agaioi ai masini. O lenei masini e tausisia le vaega 15 o Tulafono FCC. O le fa'agaioiga e fa'atatau i tulaga nei e lua:

1.  O lenei masini e le mafai ona fa'alavelave fa'alavelave
2.  e tatau ona talia e lenei masini so'o se fa'alavelave e maua, e aofia ai fa'alavelave e ono fa'atupu ai le le mana'omia.

FCC RF Radiation Faʻamatalaga Faʻaaliga:

1. O lenei Transmitter e le tatau ona tu'u fa'atasi pe fa'agaioi fa'atasi ma so'o se isi lava antenna po'o le transmitter.
2.  O nei mea faigaluega e ogatasi ma tapula'a fa'aalia o le fa'avevela RF ua fa'ata'atia mo se si'osi'omaga e le pulea.
3. O meafaigaluega nei e tatau ona fa'apipi'i ma fa'agaioi i se mamao la'ititi 20cm i le va o le radiator ma lou tino.

Gagana Peretania: O tusi lesona a le tagata fa'aoga mo masini leitio e tuusaunoaina laisene e tatau ona iai le fa'asilasilaga o lo'o mulimuli mai pe tutusa i se nofoaga iloga i totonu o le tusi fa'aoga po'o se isi mea i luga o le masini po'o mea uma e lua. O lenei masini e ogatasi ma tulaga fa'ata'ita'iga RSS e tuusaunoa laisene a Industry Canada. O le fa'agaioiga e fa'atatau i tulaga nei e lua:

1. atonu e le fa'alavelaveina lenei masini
2. e tatau ona talia e lenei masini so'o se fa'alavelave, e aofia ai fa'alavelave e ono mafua ai le fa'aogaina o le masini.

IC SAR Waring:
O nei meafaigaluega e tatau ona faʻapipiʻi ma faʻagaoioia i lalo ole mamao ole 20 cm i le va o le radiator ma lou tino.
Taua:
Ole vevela ole galue ole EUT e le mafai ona sili atu ile 85℃ ma e le tatau ona la'ititi ifo ile -40℃.
O le mea lea, Arduino Srl ta'utino atu o lenei oloa o lo'o tausisia manaoga taua ma isi aiaiga talafeagai o le Directive 2014/53/EU. O lenei oloa e faʻatagaina e faʻaaogaina i totonu o setete uma o le EU.

Fa'aili fa'avevesi	Malosi maualuga o le gaosiga (ERP)
863-870Mhz	5.47 dBm

 

Fa'asinomaga	So'oga
Arduino IDE (Lapisinisi)	https://www.arduino.cc/en/Main/Software
Arduino IDE (Ao)	https://create.arduino.cc/editor
Cloud IDE Amataina	https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino-web-editor-4b3e4a
Fono	http://forum.arduino.cc/
Nina B306	https://www.u-blox.com/sites/default/files/NINA-B3_DataSheet_%28UBX-17052099%29.pdf
ECC608	http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf
MPM3610	https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf
ECC608 Faletusi	https://github.com/arduino-libraries/ArduinoECCX08
LSM6DSL Faletusi	https://github.com/adafruit/Adafruit_LSM9DS1
LPS22HB	https://github.com/stm32duino/LPS22HB
HTS221 Faletusi	https://github.com/stm32duino/HTS221
APDS9960 Faletusi	https://github.com/adafruit/Adafruit_APDS9960
ProjectHub	https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending
Fa'asinoga Faletusi	https://www.arduino.cc/reference/en/

Fa'amatalaga Fa'amaumauga a le Kamupani

Igoa o le Kamupani	Arduino Srl
Tulaga a le Kamupani	Via Andrea Appiani 25 20900 MONZA Italia

Aso	Toe Iloiloga	Suiga
04/27/2021	1	Fa'amatalaga fa'amatalaga lautele

Pepa / Punaoa

	ARDUINO ABX00031 Nano 33 BLE Sense [pdf] Tusi Taiala ABX00031, Nano 33 BLE Sense
	ARDUINO ABX00031 Nano 33 BLE Sense [pdf] Tusi Taiala ABX00031, Nano 33 BLE Sense

Fa'asinomaga

• Tusi Taiala