ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller User Manual

ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller

Fa'amatalaga o oloa

Vaega

• E mafai ona pulea e iOS telefoni / Android telefoni
• Support “Smart Life” and “Tuya Smart” APP
• Voice control: Compatible with Alexa and Google home T mall Genie or Xiaodu speakers
• Taimi galuega: Otometi i luga / tape ma galuega taimi
• Puipuiga ova le mamafa mo le faigofie ona sui o au ki fa'ainisinia masani (mana'omia le fa'aituau)
• Vaaiga atamai
• Vaega o masini

Fa'amatalaga Puipuiga

Risk of electric shock: Electricity can cause personal injury and properly damage if not handled properly. If you are unsure of any part of these instructions, seek professional help from a qualified electrician.

Fa'apipi'i

Fa'aaliga:

• Ia mautinoa ua tapē le paoa o le ta'avale afi a'o le'i faia uaea.
• Neutral wire is required. Verify that the wall box contains a neutral wire (usually white). If the wall box does not have a neutral wire, try another location in the home or call a professional electrician to install the switch.
• O lanu uaea o loʻo faʻaalia i lenei tusi lesona o lanu masani ma e ono fesuisuiaʻi i nisi fale.
• Make sure the wire conductors are securely attached to each screw.
• Ia mautinoa o loʻo mautu le faailo Wi-Fi ma galue lelei aʻo leʻi faia le uaea.
• Afai e leai sau poto masani ile uaea, fa'amolemole vala'au ile fai eletise fa'apolofesa.

Laasaga Muamua:

• Tape le ta'avale afi ma su'e le paoa i se su'ega eletise.
• Ia mautinoa ua pe le ki a o lei faia uaea.

Laasaga Lona Lua:

• Remove existing wall panels; turn on power at breaker and use electrical tester to check which wire is the line; the tester will beep when near the line.
• Turn off the power at the circuit breaker; if there is a power outage, use an electrical tester, pull the existing switch out; mark the wiring and other wires; disconnect the power with pliers and remove the wires from the existing switch.
• Connect the switch wires to the wall box with the wire conductors according to the wiring diagram below.
• Laasaga lona tolu: Install the switch using the screws provided and snap the wall plate onto it.
• O le laasaga lona fa: Toe ki le paoa i le motumotu, ona ki lea o moli.

Ata uaea

The Live wire is connected to the “L” terminal, The Neutral wire is connected to the “N” terminal, Lighting wire is connected to “L1, L2, L3” terminals.

1. Gang switch lighting wire connection: “L1” terminal
2. Gang switch lighting wire connection: “L1,L2” terminals
3. Gang switch lighting wire connection: “L1,L2,L3” terminals

Fa'aopoopo masini

Add device to “Smart Life” or “Tuya Smart” APP

1. Step 1: Download and install the “Smart Life” or “Tuya Smart” APP: Scan the QR code below
   
2. Step 2: Enter the phone settings option, turn on the Bluetooth and WiFi functions, and turn on the product at the same time
3. Step 3: Open the Smart Life APP, register and log in your account, if you have a Smart Life account, just log in.
4. Step 4: Power on after the wiring is completed, the device is powered on by default, press and hold the touch wall switch button for about 8, until the WiFi blue LED flashes quickly, enter the network configuration mode
5. Step 5: Enter the App, click the “+” at the top right of the page to enter the network connection page.
6. Step 6: Make sure your device’s light is blinking quickly(2 times per second) tap to proceed to the next steр.
7. Step 7: Enter your WiFi and password
8. Step 8: Name your device.
9. Step 9: When the WiFi LED is on, the device is online.
   Pulea nei loa!

How to use smart speakers to control devices, such as Amazon Alexa, Google Assistant or T mall Genie?
Open the Smart Life app to enter the “Me” view and find the user Quide for “Me” view and find the user guide the corresponding smart speaker

【Note: Before using the smart speaker, please log in to your account on Amazon Alexa Google Assistant, or T mall Genie.]

Introduction of RF remote control operation

Packaged products are paired at the factory and do this wirelessly. If you need to add or replace the remote control switch, please refer to the following steps

Metotia fa'atasi
Press and hold the touch wall switch button for about 3 seconds. The red LED indicator lights up to enter the RF433 pairing mode. At this time, press the RF433 remote control switch a few times and the indicator light flashes off. The switch is controlled and paired successfully.

Auala e fa'amama tulafono

Long press the touch wall switch button for 5 seconds until the red LED indicator flashes 3 times, the code is cleared successfully.