FA'ATAU TAGATA
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
FAAMATALAGA
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
FAAMATALAGA
- Leitio Auala: 2.4 GHz (IEEE 802.15.4)
- RF Fa'aliliuga Malosi'aga: + 20dBM
- Galulue Vevela: -40° i le +70° C
- Fa'agaoioiga Susūsū: 10 i le 95%, e le fa'afefeteina
- IP66 Fa'ailoga Fa'amau
- Fua: 3.1” D x 1.6” L (80mm D x 42mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- Fa'amoemoega ole pulega: Fa'agaioiga
- Environmental: Indoor/Outdoor
- Tulaga Filogia: 3
- Faatulagaina Impulse Voltagu: 330V
MAFAUFAU FAALEAGA
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage o le 10V DC.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- Fa'alava uaea fa'apupu'u ese mai laina AC pe a mafai.
- Ole maualuga ole 4 DALI-2/D4i LED Aveta'avale ile pule, fa'afeso'ota'i le Synapse Support pe a mana'omia se fua fa'atatau.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- Aua le fa'apipi'i i se masini fa'avevela po'o se aveta'avale LED.
FAAMANATU: E tatau ona lagolagoina e le Aveta'avale LED le DIM i le OFF galuega.
LAPATA'IGA MA FA'ATOA'IGA
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- O le le mulimulitaia o nei faatonuga ma lapataiga e ono faalēaogāina ai le tusi saisai.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
FAAMATALAGA UIGA O LE TUSI ZHAGA 18 SOCKET
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
ATA 1 
FAATONUGA FA'ATA'U
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- Afai e talafeagai, aveese le pulou faʻamaufaʻailoga poʻo le masini e pulea moli o loʻo faʻapipiʻi nei i totonu o le pusa faʻapipiʻi.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
Fa'aaliga: Ina ia galue lelei, ia mautinoa o loʻo faʻaofi atoa le pule i totonu o le socket ma mimilo i le tulaga loka.
Lapataiga: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
ATA 2
TAITAIINA moli uila
| Mana o le Mana | Tulaga |
| Lanu moaga | On for 3 seconds at Startup, then Off |
| TAITAIINA tulaga | Tulaga |
| Lanu mumu | No script on the device |
| Emo Mumu | Sese Fesootaiga |
| Emo Blue | Communication, No Config |
| Emo lanumeamata | Normal Operation with Motion |
| Tape | Normal Operation, no Motion |
FA'AMATALAGA TULAFONO MA FA'AMATALAGA
Fa'amatalaga Fa'aaliga RF: O mea faigaluega nei e ogatasi ma tapula'a fa'alatalata a le FCC ua fa'ata'atia mo se si'osi'omaga e le pulea. O nei meafaigaluega e tatau ona faʻapipiʻi ma faʻagaoioia i lalo ole mamao ole 20cm i le va o le radiator ma lou tino. O lenei transmitter e le tatau ona tu'u fa'atasi pe fa'agaoioi fa'atasi ma so'o se isi antenna po'o le transmitter.
Fa'ailoga a le Industry Canada (IC): O lenei masini fa'akomepiuta e le sili atu i le Vasega B fa'atapula'a mo le fa'aosoina o leo leo mai masini fa'afuainumera o lo'o fa'ata'atia mai i Tulafono Fa'atonu a le Leitio a le Matagaluega o Feso'ota'iga a Kanata.
FCC tusipasi ma fa'amatalaga fa'atonutonu (USA)
FCC Vaega 15 Vasega B: O lenei masini e tausisia le vaega 15 o tulafono FCC. O le fa'agaioiga e fa'atatau i aiaiga nei e lua: (1) O nei masini e le mafai ona fa'alavelave fa'alavelave, ma (2) E tatau i nei masini ona talia so'o se fa'alavelave e maua, e aofia ai fa'alavelave e ono fa'atupu ai le fa'agaioiga leaga.
LEITIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): Ua uma ona faʻataʻitaʻiina lenei masini ma maua ai le tausisia o tapulaʻa mo le Vasega B masini numera, e tusa ai ma le Vaega 15 o tulafono FCC. O nei tapula'a ua mamanuina ina ia maua ai se puipuiga talafeagai mai fa'alavelave fa'alavelave i totonu o se fale fa'apipi'i. O mea faigaluega nei e gaosia, fa'aoga, ma mafai ona fa'avevela le malosi ole alaleo ma, afai e le fa'apipi'iina ma fa'aogaina e tusa ai ma fa'atonuga, e ono fa'alavelave fa'alavelave i feso'ota'iga leitio. Ae ui i lea, e leai se faʻamaoniga o le a le tupu se faʻalavelave i se faʻapipiʻi faapitoa. Afai o nei meafaigaluega e mafua ai le faʻalavelave faʻalavelave i le leitio poʻo le televise, lea e mafai ona faʻamautinoa e ala i le tape ma ola o meafaigaluega, e faʻamalosia le tagata faʻaoga e taumafai e faʻasaʻo le faʻalavelave e ala i se tasi pe sili atu o faiga nei: (1) Toe faʻaleleia. po'o le toe fa'atūina o le antenna e maua ai; (2) Faʻateleina le vavaeeseina i le va o meafaigaluega ma le faʻaputuina; (3) Fa'afeso'ota'i mea faigaluega i totonu o se so'o i luga o se ta'amilosaga e 'ese mai le mea e feso'ota'i i ai le fa'avevela; (4) Fa'afeso'ota'i le fa'atau po'o se tekinisia fa'aleoleo/TV mo se fesoasoani.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- Vaega 15, Vaega B, mo meafaigaluega Vasega B
- FCC 96-208 pe a fa'atatau ile Vasega B komipiuta patino ma peripheral
- O lenei oloa na fa'ata'ita'iina i se Fale Su'e Su'e Fa'atu i fafo ua fa'amaonia e tusa ai ma tulafono a le FCC ma ua maua e fetaui ma le FCC, Vaega 15, Emission Limits. O lo'o ola fa'amaumauga file ma maua mai le Synapse Wireless, Inc.
Afai e le o iloa le FCC ID mo le module i totonu o lenei pa o oloa pe a faʻapipiʻi i totonu o se isi masini, o le pito i fafo o le masini o loʻo faʻapipiʻiina ai lenei oloa e tatau foi ona faʻaalia se faʻailoga e faasino i le module FCC ID o loʻo faʻapipiʻiina. Suiga (FCC 15.21):
Suiga po'o suiga i nei mea faigaluega e le'i fa'amaonia manino e Synapse Wireless, Inc., e ono fa'aleaogaina ai le pule a le tagata fa'aoga e fa'agaioi ai nei masini.
Pateni – fa'ailoga fa'apitoa i https://www.synapsewireless.com/about/patents
Mo nisi fa'amatalaga asiasi: synapsewireless.com
TUSITI
| Fa'ata'ita'iga | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| Aofia le FCC ID | QOQ-GM240P |
| Aofia ai le IC | 5123A-GM240P |
| RoHS 3 | 2011/65/EU (2015/863) |
| EU REACH | (EC) No 1907/2006 |
DALI-2 Pule Talosaga Fa'amaonia
Pepa / Punaoa
 |
Synapse CSEN1 Combo Sensor Controller [pdf] Fa'atonu Taiala CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |