SURESHADE MTX2 Center Line Width

Fa'amatalaga o oloa

Fa'amatalaga

• Ituaiga Paolo: MTX2 T-Top Shade
• Umi Fa'aopoopo: Customizable based on measurements
• Mounting Component: Ata 8 Clamp
• Nofoaga e Tau ai: Tube Mount Stationary
• Canvas Color: Customizable

Fa'atonuga o le Fa'aaogaina o Mea

• Laasaga 1: Su'esu'e Nofoaga Fa'apipi'i
  Based on the MTX2 shade space requirements, mount the shade to two points on the tube 30-36 inches apart using figure 8 clamps. Ensure there is enough clearance for walking under the shade and reaching the pull bar.
• Laasaga 2: Su'e le lautele o le Paolo
  Measure the outside to outside tube dimension and tube diameter at each clamp position, ensuring an obstruction-free area of 30-36 inches.
• Laasaga 3: Su'e le maualuga o le Camber
  Determine if cambering is needed for the shade’s cross-components to conform to the hardtop’s curvature. Follow the specific instructions based on whether it is a bottom or top-mounted shade.
• Step 4: Determine If Spacers Are Needed
  Check the available mount diameter sizes and consider if spacers are required based on your measurements.

AOTELEGA

• Laasaga 1: Determine mounting area based on MTX2 shade space requirements
• Laasaga 2: Determine shade width and tube diameter
• Laasaga 3: Determine if a camber (curvature) to the shade’s cross-components (crossbars and roller) is needed
• Laasaga 4: Determine if mounting spacers are required

Laasaga 1: DETERMINE MOUNTING AREA based on MTX2 shade space requirements

• On a T-Top frame, the MTX2 shade is mounted to two points on the tube 30-36 in (762-914 mm) apart with figure 8 clamps fa'aalia i luga. Su'e po'o fea o lo'o i luga ole fa'agaau le clamps o le a tuu.
• Mafaufau pe o le a le maualuga o le paolo. E tatau ona lava le avanoa e savali ai i lalo o le paolo e aunoa ma se afaina ae aua le tele i le mea e le oo i ai le toso. E le tatau ona sili atu i le 78 in (1981 mm) le avanoa i le va o le fogafale ma le toso pa.

  

Laasaga 2: DETERMINE SHADE WIDTH. MTX2 framework (stationary actuator) and mounting clamps mana'omia se nofoaga e leai se fa'alavelave o lo'o fa'aalia i lalo.

• MTX2 shade width is specified by the “outside to outside” tube dimension – outside of PORT actuator to outside of STBD actuator. The maximum possible width for an MTX2 shade is 78” (1981 mm). Framework must be parallel for proper operation.
• A mae'a loa ona fa'amautu le vaega fa'apipi'i mo le fa'avaa o le paolo, fua ma tu'u le fua fa'atatau i FAFO i FAFO o vaega uma e lua o lo'o i ai le cl.amps o le a tuu. Fua foi ma saunia le lautele o paipa o vaega uma e lua.

  

Laasaga 3: DETERMINE CAMBER HEIGHT. The MTX2 shade’s cross-components—the outer crossbar, mid crossbar, and canvas roller—can be cambered (curved) to conform to the curvature of the hardtop. Determine if the hardtop has curvature and if camber is desired.

• Mo paolo faʻapipiʻi pito i lalo, pe a faʻamautinoa le lautele,
  1. Fa'atulaga se pito sa'o i le pito i lalo ole tumutumu malo.
  2. Fua sa'o i luga mai le ogatotonu o le lautele fuafuaina e o'o i lalo ole pito malo.
  3. Tuuina atu le fua maualuga o le pu i inisi po o le mm.

     

• Mo paolo faʻapipiʻi pito i luga, pe a faʻamautinoa le lautele,
  1. Fa'atulaga se pito sa'o i luga o le pito i luga o le malo.
  2. Fua mai le pito sa'o i le mea o le a fa'apipi'i ai le masini.
  3. Tuuina atu le fua maualuga o le pu i inisi po o le mm.

     

MAUGA TAIMI TELE MAUA

• 1.375″
• 1.50″
• 2.00″
• 2.25″
• 2.50″
• 3.00″

Fa'amolemole fa'amatalaga o le Ata 8 Mauga o faia of Anodized Alumini ao o le fa'agaioia o faia of u'ameaUamea. O lau pusa loto aofia ai pa'u ia be fa'apipi'i va o le 2 metala. If oe o le a sili o le mauga mapaipa fetaui, iina is o le filifiliga of susu vali o le mauga ma fa'agaioia paipa ma faaopoopo tau of $500.

MTX2 T-Top Shade Specifications

Va'a TAUSAGA/ FAIA/ FA'ATA'ITA'I
Ituaiga paolo			MTX2 – Pull out
Umi Faʻateleina			6FT
Fa'amauina Vaega			Ata 8 Clamp
Fa'apipi'iina			Mauga Faapau
Roller Placement			Tu'umau
tapoleni Lanu
Tulaga 1	I fafo  to Outside Tube  Width   (inches or mm)
	Tube Diameter (inches or mm)
Tulaga 2	Outside to Outside Tube Width (inisi po o le mm)
	Tube Diameter (inches or mm)
Camber Height (inches or mm)
Fuaina Avanoa Maualuluga (½ inisi [12.7 mm] fa'aopoopoga)
Customer Details COMMERCIAL SHIP TO ADDRESS AND NUMERA TELEFONI

Afai ei ai ni au fesili fa'amolemole vala'au 877-333-8323 or 215-673-2307
FA'AALIGA: O ata uma e faia i faʻamatalaga faʻapitoa. Ia mautinoa e sa'o uma fua a'o le'i tu'uina atu i lau sui o le au'aunaga. So'o se mea sese e faia e le tagata fa'atau o le matafaioi a le tagata fa'atau.

FAQ

• Can I customize the canvas color?
  Yes, the canvas color is customizable based on your preference.
• What materials are the Figure 8 Mounts and actuators made of?
  The Figure 8 Mounts are made of Anodized Aluminum, and the actuators are made of Stainless Steel. Rubber is included in the kit for installation between the two metals.
• How can I submit my measurements?
  E mafai ona e tu'uina atu au fua ile initaneti ile https://www.sureshade.com/measure/ pe imeli le pepa ua mae'a i sales@sureshade.com po'o lou sui fa'atau sa'o.

Pepa / Punaoa

SURESHADE MTX2 Center Line Width [pdf] Fa'atonu Taiala MTX2 Center Line Width, MTX2, Center Line Width, Line Width

Fa'asinomaga

• Tusi Taiala