EDA TEC ED-MONITOR-156C Alamanuia Mata'ituina ma Fa'aaliga

Fa'amatalaga o oloa

Fa'amatalaga

• Igoa Oloa: ED-MONITOR-156C
• Tufuga: EDA Technology Co., Ltd
• Aso Fa'asalalau: Aokuso 1, 2025
• Malosiaga Ulufale: 12V ~ 24V DC
• Fa'alogo leo: 3.5mm leo sio
• Ata Vitio: HDMI Ituaiga-A
• Taulaga USB: Ituaiga-C mo faailoilo mata pa'i
• Fa'amauina: VESA fetaui

Fa'atonuga o le Fa'aaogaina o Mea

• The ED-MONITOR-156C is a high-quality monitor designed for various applications.
• The monitor comes with a front panel, rear panel, and side panel, each with specific interfaces and functions.
• The front panel houses the display screen and control buttons for adjusting settings.
• The rear panel features installation holes for mounting the monitor securely.
• The side panel includes important interfaces such as power input, audio output, HDMI input, and USB touch screen port.
• The monitor includes buttons for adjusting backlight brightness and volume levels. The buttons are labeled for easy identification.
• The red power indicator on the monitor displays the power status, indicating whether the device is powered on or off.
• Each interface on the ED-MONITOR-156C serves a specific purpose, such as power input, audio output, and video input.

Tusi Lesona meafaigaluega

• O lenei mataupu o loʻo faʻaalia ai le oloa i lugaview, lisi fa'apipi'i, foliga, fa'amau, fa'ailoga, ma feso'ota'iga.

Ua umaview

O le ED-MONITOR-156C o le 15.6-inisi mata'itusi pa'i fa'apisinisi e fa'aalia ai le fa'ai'uga mata o le 1920x1080, maualuga le susulu o le 450 cd/m², ma le tele-touch capacitive touch screen. E aofia ai le tasi fa'aoga HDMI masani, tasi le Type-C USB port, tasi le DC Jack power interface, ma le tasi le 3.5mm leo leo, fa'afeso'ota'i ma 'au PC fa'amoemoe lautele. O le moli tua ma le leo e mafai ona fetuutuunai e ala i faʻamau ma polokalama, ma e faʻaaoga muamua i le faʻaogaina o mea tau pisinisi.

• The HDMI interface allows direct connection to the HDMI output of a PC host.
• The Type-C USB port transmits touch screen signals.
• The 3.5mm audio jack supports headphone connectivity.
• The DC Jack power interface supports 12V~24V DC input.

Lisi afifi

• 1x ED-MONITOR-156C Monitor
• 1 x Mounting Kit (including 4 x buckles, 4xM4*10 screws and 4xM4*16 screws)

Fa'aaliga

• O lenei vaega o loʻo faʻaalia ai galuega ma faʻamatalaga o fesoʻotaʻiga i luga o laulau taʻitasi.

Laupapa luma

• Fa'ailoaina o ituaiga ma fa'auigaina o feso'ota'iga i luga ole laulau pito i luma.

LEAI.	Fa'amatalaga
1	1 × LCD screen, 15.6-inch touch screen with a resolution of 1920×1080, multi-touch capacitive touch screen.

Laufanua Tua

• Fa'ailoaina o ituaiga ma fa'auigaina o feso'ota'iga i le pito i tua.

LEAI.	Fa'amatalaga
1	4 x installation holes of snaps, which are used to fix the snaps to the device for installation.
2	4 x VESA faʻapipiʻi pu, faʻaagaga mo le faʻapipiʻiina o puipui VESA.

Itu Laufanua

• Fa'ailoaina o ituaiga ma fa'auigaga o feso'ota'iga i luga o le laulau pito.

LEAI.	Fa'amatalaga
1	1 x red power indicator, used to view le tulaga o le malosi ma le paoa o le masini.
2	1 x DC fa'aoga, DC Jack so'oga, lea e lagolagoina 12V ~ 24V DC fa'aoga.
3	1 x 3.5mm leo fa'alogo leo fa'alogo, lagolago feso'ota'iga ulu.
4	1 x HDMI input, Type-A connector, lea e fesoʻotaʻi i le HDMI gaosiga o se PC talimalo.
5	1 x USB touch screen port, Type-C USB connector, which connects to the USB port of a PC host to transmit touch screen signals.
6	O pu e fa'afefe ai le vevela, lea e fesoasoani e fa'aleleia ai le fa'amalieina.
7	1 x Rubber plug (pre-drilled 7mm diameter circular cable routing hole), designed to accommodate additional cable management needs.
8	1 x “Brightness –” button, press the button to decrease the backlight brightness of the LCD screen.
9	1 x "Brightness +" button, oomi le ki e faʻateleina ai le susulu malamalama o le mata LCD.
10	1 x "Volume -", oomi le ki e faʻaitiitia ai le leo o le gaosiga.
11	1 x "Volume +" button, oomi le ki e faʻateleina ai le leo o le gaosiga.
12	1 x “Gūmu” fa'amau, oomi le ki e fa'alogo ai le leo o lo'o gaosia.
13	O pu e fa'afefe ai le vevela, lea e fesoasoani e fa'aleleia ai le fa'amalieina.

faamau

• ED-MONITOR-156C device includes two backlight brightness adjustment buttons and three volume adjustment buttons.
• The buttons are black in color and marked with screen-printed labels luga o le fale.

Fa'ailoga

• O le masini ED-MONITOR-156C e aofia ai se faʻailoga mumu mumu, faʻailogaina i le laupepa lolomi "PWR" i luga o le fale.

Fa'ailoga	Tulaga	Fa'amatalaga
Pwr	On	Ua ola le masini.
	Emo	Power supply of the device is abnormal. Please stop the power supply immediately.
	Tape	E le o ola le masini.

Fa'afeso'ota'i

• Faʻailoa faʻamatalaga ma galuega a faʻaoga taʻitasi i le ED-MONITOR-156C.

Mana Ofisa

• O le masini ED-MONITOR-156C e aofia ai le 1 pusa eletise faʻatasi ma le DC Jack connector, faʻailoga "24V DC" i luga o le fale. E lagolagoina 12V ~ 24V DC fa'aoga.

FAAMANATU
A 12V 4A power adapter is recommended.

HDMI Ofisa

• ED-MONITOR-156C masini e aofia ai le 1 HDMI input interface faʻatasi ma le Type-A connector, faʻaigoaina "HDMI INPUT" i luga o le fale, faʻaoga e faʻafesoʻotaʻi i le HDMI output a se PC host.

Ituaiga-C USB Interface

• ED-MONITOR-156C masini e aofia ai le 1 Type-C USB interface, faʻailoga "USB TOUCH" i luga o le fale. O lenei fa'aoga e feso'ota'i atu i le uafu USB o se PC talimalo e fa'asalalauina fa'ailo mata'i.

Fa'alogo leo

• ED-MONITOR-156C device includes 1 audio interface (3.5mm 4-pole headphone jack), labeled “ ” on the housing, supporting stereo audio output.

Fa'apipi'i le masini

• ED-MONITOR-156C device supports front embedded installation. The standard packaging includes the embedded installation Mounting kit (ED-ACCHMI-Front).

Sauniuniga

• The ED-ACCHMI-Front Mounting kit has been acquired (includes 4 × M4*10 screws, 4 × M4*16 screws, and 4 snaps).
• Ua saunia se sikuli kolosi.

Laasaga:

1. Determine the cutout dimensions on the cabinet based on the ED-MONITOR-156C’s size, as shown in the figure below.
2. Drill holes on the cabinet according to the aperture size defined in Step 1.
3. Embed the ED-MONITOR-156C into the cabinet from the exterior side.
4. Align the screw holes (non-threaded) of the snaps with the snap mounting holes on the device side.
5. Secure the snaps to the device.
   • Use 4 × M4*10 screws to fasten the snaps to the device by threading them through the non-threaded holes and tightening them clockwise.
   • Then, use 4 × M4*16 screws to secure the snaps to the cabinet: Insert them through the threaded holes of the snaps, press against the interior side of the cabinet, and thread them clockwise until fully tightened.

Fa'aaogaina o le masini

• ED-MONITOR-156C requires a PC host for operation and does not require driver installation.
• Connect it to the HDMI output of a PC host first, then power on the device to enable normal display. It supports backlight and volume adjustment via dedicated buttons and software.

Feso'ota'i Uaea

• O le vaega lea o lo'o fa'amatalaina pe fa'afefea ona fa'afeso'ota'i uaea.

Sauniuniga:

• A functional power adapter has been acquired.
• A functional PC host has been acquired.
• Functional HDMI and USB cables (Type-A to Type-C USB cable) have been acquired.

Ata fa'ata'atia o uaea feso'ota'i:
Please refer to 1.6 Interface to obtain the pin definitions and wiring methods of each interface.

FAAMANATU
The HDMI INPUT interface of the ED-MONITOR-156C is compatible with various PC hosts. The figure below illustrates cable connection using a Raspberry Pi as an example.

Fa'aola le masini

• The ED-MONITOR-156C does not include a physical power switch.
• After connecting to a power source, the device will automatically power on. Once fully booted, it will display the desktop of the connected PC host.

Adjusting brightness and Volume

• O le ED-MONITOR-156C e lagolagoina le susulu ma le leo fetuutuunai e ala i faʻamau faʻaletino ma polokalama.

Adjust brightness and volume via buttons

• O le taimi lava e fa'atino ai le ED-MONITOR-156C, e mafai ona fetu'una'i le malamalama ma le leo o le lau i tua e ala i fa'amau tu'ufa'atasi e lima i le itu.

Adjust Brightness and Volume via Software

• O le taimi lava e faʻafesoʻotaʻi ai le ED-MONITOR-156C i se PC talimalo ma faʻaalia lelei, e mafai ona fetuutuunaʻi le moli tua ma le tele o gaioiga e ala i polokalama. E eseese auala fa'agaioiga mo le Desktop ma le Lite OS versions.

Raspberry Pi OS (Lapisinisi)

• Fa'ailoaina pe fa'afefea ona fetu'una'i le malamalama i tua e ala i le UI ile Raspberry Pi OS (Desktop).

Sauniuniga:

• ED-MONITOR-156C is properly connected to the Raspberry Pi host with normal display output.
• The Raspberry Pi host has stable network connectivity.

Laasaga:

1. Add EDATEC apt repository by executing the following commands sequentially in the terminal.
2. Install the software toolkit.
3. Kiliki le icon in the top-left desktop corner. Then select to “System Tools” → “EDATEC Monitor”.
4. Adjust brightness and volume using the slider in the “EDATEC Backlight” panel.

FAAMANATU
Lagolago le faʻatinoina o le sudo ed-ddc-ui poloaiga i le faʻamalama faʻamalama e tatala ai le "EDATEC Backlight" panel.

Rasipi Pi OS (Lite)

• Fetuunaiga o le susulu ma le voluma e ala ile CLI ile Raspberry Pi OS (Lite).

Sauniuniga:

• ED-MONITOR-156C is properly connected to the Raspberry Pi host with normal display output.
• The Raspberry Pi host has stable network connectivity.

Laasaga:

1. Add the EDATEC apt repository by executing the following commands sequentially in the terminal.
2. Install the software toolkit.
3. Execute the following commands to query the current brightness level and volume level settings separately.
   • Query current brightness level:
   • Query current volume level:
4. Execute the following commands to set the brightness level and volume level as required.
   • Seti le maualuga o le malamalama:
   • Where X represents the brightness level with a range of 0~100.
   • Set volume level:
   • O le Y o loʻo faʻatusalia ai le maualuga o le voluma ma le tele o le 0 ~ 100.

FESOASOANI

• imeli: sales@edatec.cn / support@edatec.cn
• Web: www.edatec.cn
• Telefoni: + 86-15921483028(Saina) | +86-18217351262(I Fafo)

FAQ

Q: E fa'afefea ona ou fetu'una'i le malamalama i tua i luga o le mata'itū?

A: Press the Brightness button to increase the backlight brightness and the Brightness button to decrease it.

Q: E mafai ona ou fa'afeso'ota'i taligalu i lenei mata'itū mo le fa'alogo?

A: Yes, you can use the 3.5mm stereo audio output jack on the side panel to connect headphones for audio output.

Q: O le a se mea e tatau ona ou faia pe a emo le faailo o le eletise?

A: If the power indicator is blinking, it indicates an abnormal power supply. Please stop the power supply immediately and check for issues.

Pepa / Punaoa

EDA TEC ED-MONITOR-156C Alamanuia Mata'ituina ma Fa'aaliga [pdf] Tusi Taiala ED-MONITOR-156C Alamanuia Mataʻituina ma Faʻaaliga, ED-MONITOR-156C, Mataʻituina Alamanuia ma Faʻaaliga, Mataʻituina ma Faʻaaliga, ma Faʻaaliga

Fa'asinomaga

• Tusi Taiala