Batocera GPi Case and Raspberry

Add Power devices and Buttons to your Raspberry

Ina ia faʻaitiitia le tau, e le faʻapipiʻi le laupapa Raspberry Pi ma se faʻamau mana, ae e faigofie lava ona faʻaopoopo lau oe lava! O lenei ta'iala o le a fa'aali atu ai ia te oe le fa'aopoopoina o se ki fa'amalo i lau Raspberry Pi e mafai ona fa'aola/ta'oto lau masini BATOCERA.

Afai e te le mana'o e fau sau oe lava, e tele avanoa fa'apisinisi lauiloa e avanoa. O le a latou fa'aopoopoina se kilia eletise i lau Raspberry Pu, o nisi taimi e tu'uina atu ai se ili e pulea le vevela… ma fa'aopoopo se foliga matagofie i lau laupapa.

• Suiga Malosiaga Faapisinisi
  • mvave moni motusia eletise
  • O tau e tusa ma le 10-25 USD
  • E masani ona mana'omia se avanoa e fau ai i totonu
• Ki faigofie po'o ki fa'amau
  • Fa'atonu faigofie
  • Tau maualalo
  • Leai se paoa e mafai

Aisea e taua ai le ki o le Raspberry Pi?
E le tatau ona e "ave'esea" le uaea eletise mai lau Pi aua e mafai ona oʻo atu ai i le ogaoga o faʻamaumauga (ma i nisi tulaga, faʻaleagaina faaletino lau SD card). E tusa lava pe sili atu le saunia o Batocera e tetee atu i faiga pi'opi'o, e fautuaina e tapuni ma le saogalemu lau Pi e ala ile Batocera's Shutdown Menu pe sili atu, fa'aoga le ki po'o le ki.

A "tapuni" e Batocera le Pi ma se ki faigofie / latching ki, o le a tuʻuina atu i se tulaga taofi, lea e faʻaaogaina ai se vaega itiiti o le mana. E tutusa lea ma le auala e galue uma ai komepiuta faaonaponei. I totonu o lenei taʻiala o le a tatou oʻo i se tulaga tuʻu ina ia mafai ai ona tatou toe faʻaola i se taimi mulimuli ane e aunoa ma le toe faʻaaogaina o le puna eletise. E mafai ona e motusia ma le saogalemu le sapalai o le eletise (pe a e manaʻo ai) e aunoa ma le popole i faʻamatalaga piʻopiʻo aʻo i ai i le tulaga tu.

O lenei metotia e maua ai le poto masani fa'aoga sili pe a e fa'aogaina le GPi-case mai le Retroflag mo example. O lenei fale manaia e na'o le tasi le ki e ki ai/ta'i ai le Raspei. Talu ai o Batocera 5.25 o le OS e sili ona saunia mo ituaiga uma o masini eletise e fesoʻotaʻi ma le Raspberry. Ae o le ae leiloa lau taaloga SRM save (lau in-game save file) pe afai e te fa'aosoina le ki o le malosi i totonu o se ta'aloga.

Faasaoina le puipuiga o faamatalaga

1. La'u mai le fa'amatalaga o lo'o tu'uina atu i lalo
2. Faasaoina lenei mea i /userdata/system
3. Seti executable bit i le chmod +x /userdata/system/custom.sh
4. Seti lau masini eletise e tusa ai ma isi mea o loʻo i lalo

custom.sh

Suiga Malosiaga Faapisinisi

O nisi nei o su'ega eletise/fa'atauga fa'atau fa'atasi ai ma ki o lo'o lagolagoina nei. O nei mea e ofo mai ai le motusia moni o le paoa, o lona uiga ua matua tape le Raspei. E masani lava o nei masini eletise laiti e faʻapipiʻiina i luga o le Raspei e faʻaaoga ai le ulutala 40 Pin. Mo nisi fa'atonuga fa'apipi'i fa'aaoga so'oga ua tu'uina atu.
O fa'atauga nei e mafai ona e tu'u i ai system.power.switch= i le batocera.conf:

Igoa Meafaigaluega	system.power.switch	O fea e fa'atau ai ma fa'amatalaga fa'aopoopo a le gaosiga	Notes related to Batocera
Argon One mo RPi4	ARGONONE	https://www.argon40.com/argon-one-raspberry-pi-4-case.html	Get more details here
ATXRaspi	ATX_RASPI_R2_6	http://lowpowerlab.com/atxraspi/#installation
DeskPi Pro mataupu	DESKPIPRO	https://deskpi.com/collections/frontpage/products/deskpi-pro-for-raspberry-pi-4
Mausberry Circuits	MAUSEPA	http://mausberry-circuits.myshopify.com/pages/setup
msldigital PiBoard r2013	REMOTEPIBOARD_2003	http://www.msldigital.com/pages/support-for-remotepi-board-2013
msldigital PiBoard r2015	REMOTEPIBOARD_2005	http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
OneNineDesign Powerhat	POWERHAT	https://github.com/redoakcanyon/HATPowerBoard
Pimoroni OnOffShim	ONOFFSHIM	https://shop.pimoroni.com/products/onoff-shim
UUGear Witty Pi	WITTYPI	http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi	O lo'o fa'aogaina e le tusitusiga le WiringPi.
Fa'ailoga toe fo'i	RETROFLAG	http://www.retroflag.com	FOU NESPi4 lagolago!

Igoa Meafaigaluega	system.power.switch	O fea e fa'atau ai ma fa'amatalaga fa'aopoopo a le gaosiga	Notes related to Batocera
Fa'afou fu'a ma fa'amau	RETROFLAG_ADV	http://www.retroflag.com	E tutusa ma le muamua, vagana ai le ki e mafai ona faʻaosoina gaioiga, pei o le taofi o emulators
Fa'ailoga GPIO	RETROFLAG_GPI	https://www.retroflag.com/GPi-CASE.html	Maua nisi fa'amatalaga iinei.
Kintaro Super Kuma/Roshambo Retro Taaloga mataupu	KINTARO	https://www.amazon.com/dp/B079T7RDLX/?tag=electromake-20 / https://www.electromaker.io/blog/article/roshambo-retro-gaming-case-review

Fa'amau fa'atauva'a po'o sui

E mafai ona fa'aopoopo se ki e ki ai ma tape lelei lau Batocera console! Ae faapefea?

O le fea PIN GPIO e tatau ona ou fa'aogaina?
E mafai ona e fa'aopoopoina le ki fa'amalo e ki/tape ai le Batocera. O le faamau e mafai ona avea ma se faamau oomi (fa'amau mo sina taimi) po'o se ki ki (ki fa'amau). Fa'aaliga i luga o fa'amau fa'amau: o nisi GPIO o lo'o i ai ni fa'atosina e toso i totonu (tetee e feso'ota'i i le + 3.3V), o lea e sili ai le fa'aogaina o ki e masani ona tatala (fa'apu'upu'u NO) ma nei pine.

e fa'afeso'ota'i le ki i le Raspberry Pi GPIO, fa'apipi'i se PIN i le GPIO3 (fa'aletino PIN 5 i luga i le agavale) ma le isi i luga o le tele o lo'o i le itu taumatau i le itu taumatau (PIN faaletino 6)

Fa'agaoioi o le ki

GUI Menu Faiga
Get a terminal window by quitting EmulationStation with a Keyboard or get a access to terminal by SSH. Now enter /etc/init.d/S92switch setup and you will see a terminal window like in picture below. From there you can select and activate your power or switch device. The script will show you an already activated device (ONOFFSHIM in this case) and will latter show you a small message box, if the value setup was successfully set up. After this reboot the device and everything should work fine.

Fa'agaoioia tusilima
Siaki i le laulau o lo'o i luga po'o le a le ituaiga ki o le eletise e te mana'omia.
Ona fa'asa'o lea o le config file /userdata/system/batocera.conf - i le example pito i lalo ma PIN56ONOFF.

• Mo se ki fa'amau fa'asa'o batocera.conf fa'atasi ma lau fa'atonu tusitusiga ma fa'aopoopo system.power.switch=PIN56ONOFF
• Toe fai le faiga
• I le isi itu, afai e te le manaʻo e faʻasaʻo le faila ma ua e saini i totonu ma le SSH pe o iai sau faʻamau e tatala ona ulufale lea:

batocera-settings-set system.power.switch PIN56ONOFF then reboot. Your Batocera system can now be turned on/off with a button!

Toe fo'i fu'a
O le Retroflag o le tagata gaosi oloa e taula'i atu i le pusa tuai mo le Raspberry Pi fa'asologa ma mo le amataga e su'e ai ta'aloga ta'aloga. I tausaga ua tuana'i na mafai ona latou aumaia ni fale aulelei foliga matagofie i le maketi. O nei mea e musuia i masini taʻaloga mai le vaitau auro o taʻaloga taʻaloga. Afai o oe o se tagata faʻamaualuga o se GPicase, ona e vaʻai lea iinei. E ese mai le manaia o foliga o loʻo i ai pea faʻamau e galue mo le mana ma / poʻo le toe setiina e mafai. Ae e tatau ona e faia ni nai laasaga iina.

1. Fa'aaga le Suiga Tapuni Saogalemu ile PCB! O lenei ki laititi e fa'alagolago i le fale fa'aoga, va'ai i le tusi tusi mai le Retroflag pe fa'apefea ona fai lenei mea.
2. Fa'asa'o batocera.conf ma seti le faiga sui sa'o.
   • E mafai ona e fa'asa'o le faila config mai le SAMBA share ma lau fa'atonu fa'atonu tusitusiga
   • or use SSH and you can edit the config file with nano/userdata/system/batocera.conf
   • pe faʻaaoga le GUI mode, e te manaʻomia SSH mo lenei metotia, foʻi.
3. Activate or Select the correct powerswitch system.power.switch=RETROFLAG
4. Toe faʻafou, o le a faʻagaoioia ai le Safe Shutdown feature

Mo na'o le NESPi 4 mataupu
E tatau ona e faia se toe fa'aopoopo! Fa'amalie atu tama, ae e mana'omia ona matou faia se fa'aoga otometi i tua o vaaiga!

E le gata i lea, mo le NESPi4 mataupu, atonu e te oʻo i se paie faʻaaoga le HDD / SSD "cartridge". Ole feso'ota'iga Reddit lea e tu'uina atu ia te oe se auala e fa'aleleia ai (tusa lava pe na tusia le reddit post mo RetroPie, ua lipotia mai foi e OK ile Batocera).

Argon Tasi
Activate the Argon One fan by adding system.power.switch=ARGONONE in the configuration file batocera.conf.
By default, the fan starts at 55 degrees Celsius. Your can define own temperature/fan speed ladder by editing the file /userdata/system/configs/argonone.conf (it can be also edited from the network, via the SHARE SMB folder).

55=10
60=55
65=100

With this ladder, fan starts at 10% when reaching 55 degrees, and rises up to 100% when reaching 65 degrees Celsius. From the vendor recommendations, it is safe to start the fan at 55 degrees only. Less noisy. 😉

Mai:
https://wiki.batocera.org/ – Batocera.linux – Wiki

Soʻotaga tumau:
https://wiki.batocera.org/add_powerdevices_rpi_only?rev=1633139243
Fa'afouga mulimuli: 2021/10/02 03:47

https://wiki.batocera.org/

Pepa / Punaoa

Batocera GPi Case and Raspberry [pdf] Faatonuga GPi Case and Raspberry, Case and Raspberry, Raspberry

Fa'asinomaga

• Tusi Taiala