BN-LINK U135BL 7-Day Programmable Astronomical Timer Switch Instruction Manual

Folasaga

Thank you for choosing the BN-LINK U135BL 7-Day Programmable Astronomical Timer Switch. This device is designed to automate your lighting based on astronomical events like sunrise and sunset, offering convenience and energy efficiency. Please read this manual thoroughly before installation and operation to ensure proper use and safety.

Fa'amatalaga Saogalemu

• E mana'omia Uaea Neutral: A neutral wire is essential for the installation of this timer switch.
• Single Pole Only: This timer switch is designed for single-pole installations only.
• ETL Lisi: This product is ETL listed, ensuring compliance with North American safety standards.
• Fa'aeletise agavaa: Always have a qualified electrician install this product to prevent electrical hazards.
• Power Off at Breaker: Before any installation or maintenance, always cut off power at the circuit breaker to avoid electric shock.

Seti ma Fa'apipi'i

1. Unboxing ma Sauniuniga

The package includes the BN-LINK U135BL timer switch, a wall plate, mounting screws, and twist-on wire connectors. You will need a flat-head screwdriver and a Phillips head screwdriver for installation.

2. Faatonuga Uea

Taua: Ensure power is OFF at the circuit breaker before proceeding.

1. Unscrew and remove the existing wall plate and switch.
2. Verify the presence of a neutral wire in your wall box. A neutral wire is typically white.
3. Fa'afeso'ota'i le uaea uliuli of the timer to the hot wire of the wall box using a twist-on wire connector.
4. Fa'afeso'ota'i le uaea mumu of the timer to the load wire of the wall box using a twist-on wire connector.
5. Fa'afeso'ota'i le uaea paepae of the timer to the uaea le faaituau of the wall box using a twist-on wire connector.
6. Fa'afeso'ota'i le uaea lanu meamata of the timer to the uaea eleele of the wall box using a twist-on wire connector.
7. Carefully push the wired timer switch into the wall box and secure it with the provided screws.
8. Faapipii le ipu puipui.

3. Initial Power-On and System Reset

1. Turn power back ON at the circuit breaker.
2. If the screen is blank, dim, or flashing, allow the internal battery to charge for 10 minute.
3. Press the "RESET" button to reset the system. The screen display will flash.
4. Hold the "SET" button for 3 sekone to quit the flashing clock display.

Fa'aaliga: The system time and all settings will be erased after a system reset.

4. Setting Current Date, Time, and Sunrise/Sunset Time

Follow these steps to configure the basic time settings:

1. Seti Tausaga: Press "SET". The year (e.g., 2018) will flash. Use "+" or "-" to set the current year (from 2018 to 2099).
2. Set Month and Day: Press "SET" again to confirm the year. The month and day will flash. Use "+" or "-" to set the current date (from 1.1 to 12.31).
3. Set Hour and Minute: Press "SET" again to confirm the date. The hour and minute will flash. Use "+" or "-" to set the current time (from 12:00 AM to 11:59 PM). Ensure you select the correct AM/PM format.
4. Confirm Time and DST: Press "SET" to confirm the correct time. Then use "+" or "-" to set DST (Daylight Saving Time) to ON or OFF. Enable DST if your region observes it to avoid manual adjustments.
5. Filifili Sone Taimi: Press "SET" to confirm DST setting. The Time Zone will flash. Use "+" or "-" to choose your local time zone from PAC (Pacific), MOU (Mountain), CEN (Central), EAS (Eastern), HAW (Hawaii), and ALA (Alaska).
6. Set Sunrise/Sunset Time: Press "SET" to confirm the current time zone. The sunrise time will flash. Use "+" or "-" to set the correct sunrise time for your time zone. Press "SET" again, and the sunset time will flash. Use "+" or "-" to set the correct sunset time.
7. Tu'u ese Fa'asaga: Press "SET" to confirm the sunset time and exit the setting process. If you are in Daylight Saving Time, check if the DST icon is displayed.

Motugaafa: If you want to quit setting at any stage, hold "SET" for 3 seconds or leave the buttons untouched for 90 seconds. Pressing "+" or "-" once changes values by one unit. Holding for less than 2 seconds changes by 6-8 units/second. Holding for 2 seconds or more changes by 60 units/second.

Fa'atonuga o Galuega

1. Setting ON and OFF Events (Programs)

The timer switch supports up to 18 ON/OFF programs. To set a program:

1. Press "PROG". The display will show "--:--".
2. Press "SET" to set the first ON event. The day of the week will flash first. Use "+" or "-" to choose the desired day(s) or day combination (e.g., MO TU WE TH FR SA SU, MO, TU, WE, TH, FR, SA, SU, MO TU WE TH FR, SA SU).
3. Press "SET" to confirm the day(s). The time will flash. Use "+" or "-" to set the desired ON time (from 12:00 AM to 11:59 PM). If you want to choose sunrise or sunset time as the ON time, press the 'D/D' button once for sunrise or twice for sunset.
4. Press "PROG" to confirm the ON event. The display will show "--:--" again.
5. Press "SET" to set the first OFF event. The day of the week will flash first. Use "+" or "-" to choose the desired day(s) or day combination.
6. Press "SET" to confirm the day(s). The time will flash. Use "+" or "-" to set the desired OFF time (from 12:00 AM to 11:59 PM). If you want to choose sunrise or sunset time as the OFF time, press the 'D/D' button once for sunrise or twice for sunset.
7. Press "PROG" to confirm the OFF event. The display will show "--:--" again.
8. Repeat steps 2.2 to 2.6 to set additional programs, up to a maximum of 18.

Motugaafa: To quit event setting at any stage, hold "PROG" for 3 seconds or leave the keys untouched for 90 seconds. To clear or resume the current input, press either the ON/OFF key once or twice. To revise a previous input, press 'SET' to shift to the relevant stage and make the correction.

2. Faiga Taavale/Taulima

This timer switch has two operating modes: MANUAL (MAN ON/MAN OFF) and AUTO (AUTO ON/AUTO OFF).

• Fa'aliliuina Faiga: After completing program setup, press and hold the ON/OFF button for 3 seconds or longer to switch between MANUAL and AUTO modes.
• Faiga MANUAL: Press ON/OFF to turn the timer constantly ON or OFF.
  • MAN ON: O lo'o ola pea le eletise.
  • TAGATA OFF: E PI pea le eletise.
• Faiga AUTO: Press ON/OFF to temporarily turn the timer ON or OFF.
  • AUTO OFF: Power output is temporarily cut off and will be resumed upon the next ON event.
  • AUTO ON: Power output is temporarily active and will be cut off upon the next OFF event.

Fa'aaliga: Ensure the timer switch is set to AUTO mode for it to operate based on the programmed settings.

3. Daylight Savings Time (DST) Mode

The DST mode automatically adjusts the time, eliminating the need for manual changes and ensuring accurate lighting control year-round.

• Activate/Deactivate DST: Temporarily activate or deactivate DST by holding the "+" button for 3 seconds.
• When DST is ON, the DST icon will be displayed on the screen.
• When DST is OFF, the icon will disappear.

4. Random Mode

Activate the "Random" vacation mode to randomize light schedules, creating the illusion that your home is occupied to deter potential intruders.

• Activate/Deactivate Random Function: Press and hold "-" for 3 seconds or more to activate or deactivate the random function.
• When this function is active, the "RND" icon will display.
• At least one program must be set before activating the random function.
• When the random function is active, the ON and OFF events will be randomly postponed by 0-30 minutes respectively.

Tausiga

The BN-LINK U135BL timer switch requires minimal maintenance. Ensure the device is kept clean and free from dust. Do not use abrasive cleaners or solvents. In case of any issues, refer to the troubleshooting section or contact customer support.

Fa'afitauli

Problem 1: No screen display or faded display.

Mafua'aga e ono tupu: Ma'a maualalo.

Fa'asa'oga Fa'atonu: Energize the timer to charge the internal battery for 10 minutes, then press the "RESET" button to reset the timer.

Problem 2: Timer does not turn on or off as programmed.

Possible Cause A: O lo'o galue le taimi ile fa'aoga tusilima.

Fa'asa'oga Fa'atonu: Switch the operation mode to AUTO by holding the ON/OFF button for 3 seconds.

Possible Cause B: O lo'o galue le galuega fa'afuase'i.

Fa'asa'oga Fa'atonu: Deactivate random function by holding the "-" button for 3 seconds.

Possible Cause C: DST is disabled, while the device is located in a region that observes DST. As a result, the internal time was not adjusted when DST started or ended, causing the scheduled operations to run at incorrect times.

Fa'asa'oga Fa'atonu: Enable DST by following the time setting procedure on the timer switch (hold "+" for 3 seconds).

Possible Cause D: Current system time on the timer switch is incorrect.

Fa'asa'oga Fa'atonu: Verify and correct the current time setting on the device by following the time setting procedure on the timer switch.

Possible Cause E: E le'i sa'o le setiina o polokalame.

Fa'asa'oga Fa'atonu: Re-program the timer following the operating instructions in this manual.

Fa'amatalaga

Fa'amatalaga Fa'amaonia

BN-LINK products are designed to provide reliable performance. For specific warranty details, please refer to the documentation included with your purchase or contact BN-LINK customer support. Keep your purchase receipt as proof of purchase for warranty claims.

Lagolago Tagata Fa'atau

If you require further assistance or have any questions regarding your BN-LINK U135BL Astronomical Timer Switch, please contact our support team:

• imeli: support@bn-link.com
• Webnofoaga: Visit the BN-LINK Store on Amazon

Ua matou i ai iinei e fesoasoani!