MIEFL Toilet Light Motion Sensor (2 Pack) User Manual

Folasaga

This manual provides comprehensive instructions for the setup, operation, and maintenance of your MIEFL Motion Sensor Toilet Light. Please read this manual thoroughly before use to ensure proper functionality and longevity of the product.

O mea o lo'o i totonu

Fa'amautinoa o lo'o iai mea uma i lau afifi:

• 2 x MIEFL Motion Sensor Toilet Lights
• Tusi Lesona a le Tagata (lenei pepa)

Note: 3 AAA batteries per unit are required and are not included in the package.

Seti ma Fa'apipi'i

1. Fa'apipi'i ma'a

1. Locate the battery compartment on the back of the toilet light unit.
2. Tatala le ufiufi o le vaega o maa.
3. Fa'aofi 3 maa AAA, fa'amautinoa le sa'o o le polarity (+/-).
4. Tapuni lelei le ufiufi o le vaega o maa.

Figure 1: Battery installation for the MIEFL Toilet Light. Ensure correct battery orientation.

2. Fa'amauina o le Masini

1. Adjust the flexible arm of the toilet light to fit over the rim of your toilet bowl.
2. Position the main unit on the outside of the toilet bowl, ensuring the motion sensor faces outwards and upwards.
3. Ensure the LED light strip is positioned inside the toilet bowl, below the rim, and securely in place.

Figure 2: Step-by-step guide for mounting the toilet light onto the toilet bowl rim.

Fa'atonuga o Galuega

Motion and Light Sensing

The MIEFL Toilet Light is equipped with both motion and light sensors:

• Fa'agaioiga Fa'agaioiga: The light will activate when motion is detected within approximately 6.6 feet (2 meters).
• Lagona malamalama: The device is designed to operate only in dark conditions to conserve battery life. It will not activate in a well-lit environment.
• Otometi tapunia-ese: The light will automatically turn off after approximately 2 minutes of no detected motion.

Figure 3: The toilet light's smart sensing capabilities for night activation and daytime energy saving.

Filifiliga Lanu

The toilet light offers 16 different colors. By default, the light cycles through all 16 colors. To select a fixed color:

1. Locate the small button on the side of the main unit (labeled 'Color Control Switch' in Figure 4).
2. Press this button once while the light is cycling through colors. The light will stop on the current color.
3. To return to the color-cycling mode, press the button again.

Figure 4: Location of the Color Control Switch and Motion Sensor on the MIEFL Toilet Light.

Fetuunaiga Malamalama

The toilet light features 5 brightness levels and automatically adjusts its brightness based on ambient light conditions. This feature is designed to optimize power consumption and extend battery life.

Tausiga

Fa'amamaina

To clean your MIEFL Toilet Light:

• Remove the unit from the toilet bowl.
• Solo le iunite i fa'asalalaugaamp ie ma fufulu mama.
• Do not submerge the main unit in water. The LED strip is waterproof, but the main unit containing electronics is not designed for full submersion.
• Ensure the unit is completely dry before re-installing or replacing batteries.

Figure 5: The LED light strip is waterproof for easy cleaning.

Suiga maa

When the light begins to dim or fails to activate, it is time to replace the batteries. Follow the steps outlined in the 'Battery Installation' section (Section 1.1).

Fa'afitauli

Fa'amatalaga o oloa

Fa'amaonia ma Lagolago

MIEFL products are designed for reliability and performance. For specific warranty details, please refer to the product packaging or contact MIEFL customer support directly. If you encounter any issues not covered in the troubleshooting section, please reach out to the seller or manufacturer for assistance.