Phocos CIS10 IP68 10Amp Tusitaiala a le Pule Pulea o le Solar

1. Folasaga

This manual provides essential instructions for the safe and efficient operation of your Phocos CIS10 IP68 10Amp Solar Charge Controller. The CIS10 is designed for off-grid solar light systems and battery charging, featuring automatic 12V/24VDC system voltage detection and a robust IP68 waterproof design. Please read this manual thoroughly before installation and use.

2. Fa'amatalaga Saogalemu

Fa'atonuga Saogalemu Taua:

• Always connect the battery to the charge controller first, then the solar panel, and finally the load. Disconnect in the reverse order.
• Ensure all connections are tight and secure to prevent excessive voltage drop and loose connections.
• Install the controller in a well-ventilated area, away from flammable gases.
• Do not disassemble or attempt to repair the controller yourself. Contact qualified personnel for service.
• Wear appropriate personal protective equipment (PPE) when working with batteries and solar panels.
• The controller is IP68 rated for water and dust ingress, but avoid submerging it for extended periods or exposing it to high-pressure water jets.

3. Vaega o Oloa

The Phocos CIS10 Solar Charge Controller offers the following key features:

• IP68 le Suavai Design: Suitable for outdoor use, resistant to water spray, rain, and condensation.
• Otometi Voltagu Su'esu'ega: Otometi ona iloa 12V po o 24V DC faiga voltages.
• 5-Stage PWM Technology: Provides Soft Start, Bulk, Absorption, Float, and Equalization charging stages for optimal battery health and system performance.
• Wide Battery Compatibility: Works with LifePo4, LTO, GEL, AGM, Lead-Acid, Calcium, and EFB batteries.
• Vaega e Puipuia Tele: Built-in protection against over-temperature, over-voltage, over-current, over-charging, over-discharging, overload, and short circuits.
• Compact and Thin Design: Maximizes solar power utilization with minimal self-power consumption.

4. Seti ma Fa'apipi'i

Follow these steps for proper installation of your Phocos CIS10 controller:

1. Fa'amauina: Choose a suitable location for mounting the controller. Although IP68 rated, mounting in a shaded or protected area can extend its lifespan. Ensure adequate space for cable connections.
2. So'oga ma'a: Connect the battery cables to the controller's battery terminals first. Ensure correct polarity (positive to positive, negative to negative). The controller will automatically detect the system voltage (12V poʻo le 24V).
   

   Image 4.1: Phocos CIS10 controller showing battery, solar panel, and load connection points, along with LED indicators for status.

3. So'oga o le Solar Panel: Connect the solar panel cables to the controller's solar panel terminals. Observe correct polarity. The controller will begin charging the battery.
4. Load Connection (Optional): If using the controller for a DC load (e.g., solar light), connect the load cables to the controller's load terminals. Ensure correct polarity.
5. Fa'amaonia So'oga: Double-check all connections for tightness and correct polarity before powering on the system.

The controller's compact design and integrated wiring simplify installation. Its IP68 rating ensures durability in various outdoor conditions.

Image 4.2: The Phocos CIS10 controller demonstrating its compact size with a ruler and highlighting its IP68 waterproof capability.

5. Fa'atonuga o Galuega

The Phocos CIS10 operates automatically once connected. It utilizes advanced 5-stage Pulse Width Modulation (PWM) charging technology to optimize battery charging and extend battery life.

5.1. Ua molia Stages

• Amataga Filemu: Gradually increases current to the battery.
• Totogi tele: Tuuina atu le maualuga o le taimi nei e faʻavaveina ai le maa i le tusa ma le 80% le gafatia.
• Totogi fa'asusu: Charges the battery at a constant voltage to bring it to 100% capacity.
• Totonu Totogi: Fa'atumauina le ma'a i se tau atoa e ala i le tu'uina atu o se vol itiiti, faifai peatage.
• Fa'atusa: Automatically performs equalization every 28 days for calcium/EFB batteries to prevent sulfation and ensure cell balance.

5.2. Work Mode (Optional)

The CIS10 controller supports configurable work modes, such as time control and light control, which can be set using an optional external unit like the CIS-CU (sold separately). This allows for customized operation of connected loads, such as solar lights.

6. Tausiga

The Phocos CIS10 is designed for minimal maintenance due to its robust IP68 rating and epoxy-encapsulated PCB. However, periodic checks are recommended:

• Su'ega Va'ai: Periodically inspect the controller and all connections for any signs of damage, corrosion, or loose wiring.
• Fa'amamaina: If necessary, gently clean the exterior of the controller with a damp ie. Aua ne'i fa'aogaina vaila'au malolosi po'o mea fa'afefete.
• Soifua Maloloina maa: Monitor your battery's performance. The controller's equalization feature helps maintain battery health for compatible types.

7. Faʻafitauli

The CIS10 controller includes multiple built-in protections to prevent damage. If you encounter issues, consider the following:

• No Charging/Load Output:
  • Check all wiring connections for tightness and correct polarity.
  • Ia mautinoa o loʻo maua e le la o le la le susulu o le la.
  • Fa'amaonia maa voltage is within the operating range (12V/24V).
  • Check for any blown fuses in the system (if applicable).
• Puipuiga o le Vave: If the controller becomes excessively hot, it may temporarily reduce or stop charging/output. Ensure it's not installed in an area with poor ventilation or direct, intense heat.
• Sili-Voltage/I lalo-Voltagu Puipuiga: The controller will protect the battery from overcharging or deep discharge. If the battery voltage is too low, the load may be disconnected.
• Short Circuit/Overload Protection: If a short circuit or overload occurs on the load or solar input, the controller will temporarily shut down to protect itself and the system. Remove the fault and the controller should resume normal operation.

If problems persist, refer to the detailed specifications or contact Phocos customer support.

8. Fa'amatalaga

Detailed technical specifications for the Phocos CIS10 Solar Charge Controller:

9. Fa'amaonia ma Lagolago

Phocos is a German brand known for quality assurance in solar power products. For warranty information, technical support, or service inquiries, please contact your authorized Phocos dealer or visit the official Phocos webnofoaga. Taofi lau lisiti fa'atau mo tagi fa'amaonia.

For additional resources and product updates, you may visit the Phocos official webnofoaga.