Tusitaiala mo le Behringer EUROLIVE VQ1800D Active PA Subwoofer

1. Folasaga

This manual provides essential information for the safe and efficient operation of your Behringer EUROLIVE VQ1800D Active PA Subwoofer. Please read this manual thoroughly before operating the device to ensure proper setup, usage, and maintenance. Retain this manual for future reference.

Ata 1.1: Luma view of the Behringer EUROLIVE VQ1800D Active PA Subwoofer.

2. Faatonuga Saogalemu

Ia matau i taimi uma ia puipuiga saogalemu nei e faʻaitiitia ai le lamatiaga o le teʻi eletise, afi, poʻo manuʻaga:

• Paoa sapalai: Fa'afeso'ota'i le masini na'o le voltage specified on the unit. Ensure the power cable is not damaged and is routed safely to prevent tripping hazards.
• Savili: Do not block ventilation openings. Install the device in a location with adequate airflow to prevent overheating.
• Susū ma le vevela: Do not expose the device to rain, moisture, dripping or splashing liquids. Keep away from direct heat sources or extreme temperatures.
• Tu'uga: Place the subwoofer on a stable, level surface. Avoid placing it in direct sunlight or near strong magnetic fields.
• Puipuiga Fa'alogo: Prolonged exposure to high sound pressure levels can cause permanent hearing damage. Use appropriate hearing protection when operating the subwoofer at high volumes.
• Au'aunaga: Aua le taumafai e fa'aleleia oe lava lenei masini. Fa'asino uma auaunaga i tagata faigaluega agavaa.

3. Mea i totonu o le afifi

Fa'amautinoa o lo'o iai mea uma pe a uma ona tatala:

• 1 x Behringer EUROLIVE VQ1800D Active PA Subwoofer
• 1 x Uaea Malosi
• Tusi Faʻatonuga (lenei pepa)

4. Seti

Follow these steps for initial setup of your subwoofer:

4.1. Tulaga Faaletino

Position the VQ1800D subwoofer on a stable, flat surface, preferably on the floor, to maximize bass response. Ensure there is adequate space around the unit for ventilation.

Ata 4.1: Esoample setup with the VQ1800D subwoofer and full-range speakers.

4.2. So'oga

The VQ1800D features a built-in stereo crossover, allowing you to connect full-range loudspeakers directly to its outputs.

1. So'oga Malosi: Connect the supplied power cable to the AC inlet on the rear panel of the subwoofer and then to a suitable mains power outlet.
2. Fa'alogo leo: Connect your audio source (e.g., mixer, audio interface) to the XLR input connectors (INPUT 1 or INPUT 2) on the rear panel.
3. Audio Output (to Full-Range Speakers): If using the built-in stereo crossover, connect your full-range loudspeakers to the XLR output connectors (OUTPUT 1 or OUTPUT 2). These outputs provide a high-pass filtered signal to your main speakers, optimizing their performance.

Image 4.2: Rear panel showing input/output connections and controls.

5. Fa'atonuga o Galuega

5.1. Malosi i luga/Pepe

1. Ia mautinoa o lo'o malupuipuia so'otaga uma a'o le'i fa'aola.
2. Press the POWER switch on the rear panel to turn the subwoofer on. The power LED will illuminate.
3. To power off, press the POWER switch again.

5.2. Adjusting Volume and Crossover

The VQ1800D features controls for fine-tuning its performance:

• Pulea o le Tulaga: Adjusts the overall output volume of the subwoofer. Start with a low setting and gradually increase to your desired level.
• BOOST Frequency: Allows you to select a specific frequency range (40 Hz to 90 Hz) to boost for enhanced bass impact.
• HIGH CUT Control: Sets the crossover frequency for the subwoofer (70 Hz to 150 Hz). This determines the upper frequency limit of the subwoofer's output and the lower frequency limit of the signal sent to your full-range speakers via the 'PASS THRU' outputs.
• FASE Suiga: Inverts the phase of the subwoofer's output. Experiment with this setting to achieve optimal bass alignment with your main speakers.
• LIMIT LED: Illuminates when the internal limiter is active, indicating that the signal is too high and clipping may occur. Reduce the input level or the LEVEL control if this LED is constantly lit.

Ata 5.1: Auiliiliga view of the control panel for volume, boost, and crossover settings.

6. Tausiga

Regular maintenance ensures the longevity and optimal performance of your subwoofer:

• Fa'amamaina: Use a soft, dry cloth to clean the exterior of the subwoofer. Do not use abrasive cleaners or solvents.
• Savili: Periodically check that the ventilation openings are free from dust and debris.
• Teuina: When not in use for extended periods, store the subwoofer in a dry, cool environment, protected from dust and extreme temperatures.
• Asiasiga: Regularly inspect the power cable and audio cables for any signs of damage. Replace damaged cables immediately.

7. Faʻafitauli

If you encounter issues with your VQ1800D subwoofer, refer to the following common troubleshooting steps:

• Leai se Malosi: Ensure the power cable is securely connected to both the subwoofer and the power outlet. Check the power switch position and the mains fuse.
• Leai se leo: Verify that the audio source is active and connected correctly to the subwoofer's inputs. Check the LEVEL control setting. Ensure any connected full-range speakers are also powered on and receiving a signal from the subwoofer's outputs.
• Distorted Sound / LIMIT LED Constantly On: Reduce the input signal level from your audio source or lower the subwoofer's LEVEL control. The LIMIT LED indicates that the amplifier is being overdriven.
• Bass vaivai: Check the PHASE switch setting. Experiment with both positions to find the optimal phase alignment with your main speakers. Ensure the HIGH CUT frequency is set appropriately for your system.

If the problem persists after attempting these steps, contact qualified service personnel.

8. Fa'amatalaga

9. Fa'amaonia ma Lagolago

The Behringer EUROLIVE VQ1800D Active PA Subwoofer comes with a limited warranty. For detailed warranty information, product registration, and technical support, please visit the official Behringer webnofoaga po'o fa'afeso'ota'i lau fa'asoa fa'apitonu'u.

For further assistance, refer to the contact information provided on the product packaging or the official Behringer support channels.