AMDP Power Programmer Taiala mo Tagata Fa'aoga
FA'amolemole faitau fa'atonuga a'o le'i fa'aaogaina
TAUA MO TAGATA UMA
E aofia i le Power Programmer kit o se uaea fa'alautele pupuu ma uaea moli. O lenei fa'apotopotoga uaea e NA'O le fa'aaogaina i luga ole L5P Duramax ECM tatala fa'agasologa! E LEʻI faʻaaogaina mo soʻo se Powerstroke talosaga!
ITULAU 1 – Laasaga Muamua i le Fa'aaogaina o le Auto Flasher
E tatau ona iai sau Windows 10 poʻo se komepiuta sili atu e faʻaoga ai le polokalama Auto Flasher.
Laasaga 1: Sii mai le polokalame Power Programmer mai https://www.dirtydieselcustom.ca/pages/instructions
Laasaga 2: Sii mai le Power Programmer USB Avetaavale mai https://www.dirtydieselcustom.ca/pages/instructions
Laasaga 3: I le Downloads i luga o lau komepiuta, Tatala, Aveese, Tamomoe, ma Faʻapipiʻi le VCP USB Drivers 64bit. Mulimuli i faatonuga seia mae'a.
Laasaga 4: I le Downloads i luga o lau komepiuta, Tatala, Tamomoe, ma Faʻapipiʻi Auto Flasher. Atonu e tatau ona e tape le polokalame anti-virus e mafai ai ona e fa'apipi'i le polokalama Auto Flasher.
Laasaga 5: Tatala Auto Flasher, atonu e faʻamalosia oe e faʻafouina i le lomiga fou. Kiliki "Ioe" ma mulimuli i faʻatonuga e faʻafou i le lomiga lata mai.
Laasaga 6: NA'O fa'apipi'i le Power Programmer module (pusa uliuli) i le USB i le taimi nei, e leai se isi uaea.
Laasaga 7: Kiliki Cable> Fesoʻotaʻi> Uaea> Faʻafouina Firmware. Mulimuli i ta'amilosaga USB e fa'afou ai le firmware.
Laa 8: A maeʻa loa le firmware, kiliki Cable> Fesoʻotaʻi. Ua tatau nei ona e va'ai i le CABLE ID o lo'o ola i le pito i luga taumatau o le polokalama ma ua e sauni e alu!
ITULAU 2: 2020-2021 6.7L Powerstroke Engine Fa'alogo Na'o
Laasaga 1: Su'e le PCM i luga o le pa puipui o le pasese ma motusia uma feso'ota'iga 3.
Laasaga 2: Fa'afeso'ota'i le fa'aogaina o le eletise i le maa o le ta'avale (fa'amautinoa le polarity sa'o).
Laasaga 3: Faʻafesoʻotaʻi le Power harness i le AMDP Power Programmer, ona faʻafesoʻotaʻi lea o le fesoʻotaʻiga PCM tuʻuina atu i le PCM pito sili ona pasese i luga o le taʻavale.
Laasaga 4: Faʻafesoʻotaʻi le AMDP Power Programmer i le Windows based Laptop faʻatasi ai ma le polokalama na taʻua muamua ua faʻapipiʻiina.
Laasaga 5: Tatala le polokalama AutoFlasher, filifili "Cable", ona Filifili "Fesoʻotaʻi". Afai e manuia le fesoʻotaʻiga alu i le Laasaga 6, pe a le toe faʻapipiʻi le USB Drivers ma siaki fesoʻotaʻiga USB.
Laasaga 6: Filifili le "Service Mode", ona "Power On". O le savali "Powering on module" e tatau ona aliali mai.
Laasaga 7: Filifili le "Auaunaga Auala", ona "Faailoa". Faamaonia le PCM o loʻo fesoʻotaʻi ma. Afai e leai, siaki fesoʻotaʻiga eletise ma toe fai le Laasaga 6. O le Cable S / N, ECU S / N ma le VIN e tatau ona imeli i sales@amdieselperformance.ca ma lau numera oka AMDP ma po'o ai na e fa'atonuina e maua ai le fa'atau fa'atau. Ina ia kopi numera ta'itasi kiliki sa'o ona Ctrl-V ile imeli.
Laasaga 8: A uma ona e mauaina fati e ala ile imeli, fa'asaoina i lau komepiuta. Toe fai Laasaga 1-7 pe afai ua motusia le ta'avale.
Laasaga 10: Filifili le "Service Mode", ona "Tusi", ona "ECU", filifili le file na imeli muamua atu ia te oe. O le a amata nei le faiga fa'alogo. A uma loa e mafai ona e motusia uma so'otaga AMDP Power Programmer ma toe fa'afeso'ota'i feso'ota'iga PCM falegaosimea.
Laasaga 11: Ia mautinoa e amata le taʻavale ma e leai ni tulafono a le DTC poʻo ni feʻau faʻailoga o loʻo iai. Afai ei ai se mea fa'amolemole fa'afeso'ota'i le lagolago fa'atekinolosi.
ITULAU 3: 2022 6.7L Powerstroke Aveese Na'o le Fa'ainitaneti
Faamolemole Manatua: 2022 Aveese Na'o le fa'alogo E TATAU ona iai le EGR ma le Throttle Valves i le nofoaga ma feso'ota'i i le taimi nei.
Laasaga 1: Su'e le PCM i luga o le pa puipui o le pasese ma motusia uma feso'ota'iga 3.
Laasaga 2: Fa'afeso'ota'i le fa'aogaina o le eletise i le maa o le ta'avale (fa'amautinoa le polarity sa'o).
Laasaga 3: Faʻafesoʻotaʻi le Power harness i le AMDP Power Programmer, ona faʻafesoʻotaʻi lea o le fesoʻotaʻiga PCM tuʻuina atu i le Pasenger side PCM plug i luga o le taʻavale.
Laasaga 4: Faʻafesoʻotaʻi le AMDP Power Programmer i le Windows based Laptop faʻatasi ai ma le polokalama na taʻua muamua ua faʻapipiʻiina.
Laasaga 5: Tatala le polokalama AutoFlasher, filifili "Cable", ona Filifili "Fesoʻotaʻi". Afai e manuia le fesoʻotaʻiga alu i le Laasaga 6, pe a le toe faʻapipiʻi le USB Drivers ma siaki fesoʻotaʻiga USB.
Laasaga 6: Filifili le "Service Mode", ona "Power On". O le savali "Powering on module" e tatau ona aliali mai.
Laasaga 7: Filifili "OBD", ona "Faailoa". Faʻamaonia le PCM o loʻo fesoʻotaʻi ma. Afai e leai, siaki feso'ota'iga eletise ma toe fai le Laasaga 6.
Laasaga 8: Filifili "OBD", ona "Maua VIN". Ole Cable S/N, ECU S/N ma le VIN e tatau ona imeli ile sales@amdieselperformance.ca ma lau numera oka ma po'o ai na e fa'atonuina e maua ai le fa'atau fa'atau. Ina ia kopi numera ta'itasi kiliki sa'o ona Ctrl-V ile imeli.
Laasaga 9: A uma ona e mauaina fati e ala ile imeli, fa'asaoina i lau komepiuta. Toe fai Laasaga 1-7 pe afai ua motusia le ta'avale.
Laasaga 10: Filifili "OBD", ona "Tusi", ona "ECU", filifili le file na imeli muamua atu ia te oe. O le a amata nei le faiga fa'alogo. A uma loa e mafai ona e motusia uma so'otaga AMDP Power Programmer ma toe fa'afeso'ota'i feso'ota'iga PCM falegaosimea.
Laasaga 11: Ia mautinoa e amata le taʻavale ma e leai ni tulafono a le DTC poʻo ni feʻau faʻailoga o loʻo iai. Afai ei ai se mea, fa'amolemole fa'afeso'ota'i le lagolago fa'atekinolosi.
ITULAU 4: 2022 6.7L Powerstroke Power Engine Tuning & PCM Swap
Laasaga 1: Faʻafesoʻotaʻi le AMDP Power Programmer i le OBD2 Port o le taʻavale ma faʻamalama faʻapipiʻi komepiuta feaveaʻi ona liliu lea o le ki i le tulaga Run / On.
Laasaga 2: I le Autoflasher software, filifili "Cable" -> "Fesoʻotaʻi". Afai na manuia le feso'ota'iga, alu i le Laasaga 5.
Laasaga 3: Filifili "OBD" -> "AsBuilt" -> "Faitau". I le faʻamalama faʻapipiʻi filifili "ECU" ona filifili lea "Ulufale". Faasaoina le AsBuilt data (didsRead).
Laasaga 4: Filifili le "Cable" -> "Disconnect". Aveese le Polokalama mai le OBD2 Port.
Laasaga 5: Faʻapipiʻi le PCM Fou ma faʻafesoʻotaʻi le Polokalama i le PCM e ala i le PCM faʻapipiʻi. Ia mautinoa ua motusia uma isi feso'ota'iga PCM.
Laasaga 6: Filifili le "Service Mode" -> "Faitau EE". Faasaoina le file (EE_Faitau).
Laasaga 7: Imeli le Cable S / N ma le ECU S / N e ala i le kiliki saʻo i luga o taʻitasi ma faapipii i totonu o le imeli ma le numera o le Poloaiga, VIN ma o ai na e faʻatonuina e maua ai lau faʻalogo.
Laasaga 8: Filifili le "Auaunaga" -> "Power Off".
Laasaga 9: Filifili le "Cable" -> "Disconnect"
Laasaga 10: A maeʻa ona e mauaina le afi afi, filifili le "Cable" -> "Connect", ona filifili lea o le "Service Mode", "Write", Filifili le fati.
Laasaga 11: A faʻaalia le Flash Successful, Filifili le "Service Mode" -> "Power Off".
Laasaga 12: Filifili le "Cable" -> "Disconnect"
Laasaga 13: Faʻafesoʻotaʻi le PCM Fou i le Taʻavale Taʻavale
Laasaga 14: Faʻafesoʻotaʻi le Polokalama ile OBD2 Port ma liliu le ki ile On / Run Position.
Laasaga 15: Filifili "OBD" -> "AsBuilt" -> "Tusi", filifili faʻamaumauga AsBuilt na faʻasaoina muamua (didsRead), filifili "ECU", ona filifili lea "Ulufale".
Laasaga 16: Filifili le "OBD" -> "Misc Routines" -> "Configuration Relearn", filifili "ECU", ona filifili lea "Ulufale". Mulimuli i le 30 sekone fa'anaunauga mo Key On, ona tape lea. A uma loa ona toe ki.
Laasaga 17: Laasaga 6: Filifili "OBD" -> "Misc Routines" -> "PATs" -> "BCM EEPROM Faitau". Faasaoina le file. Afai e umi le 10 minute o le faitauga o le BCM, tape uma uaea mai le Programmer ma tapuni le polokalama Autoflasher. Fa'asolo le ki fa'amumu, toe tatala le polokalama, toe fa'afeso'ota'i le Polokalama ma toe taumafai.
Laasaga 18: Filifili le "OBD" -> "Misc Routines" -> "PATs" -> "PATs Reset". Filifili le "Ioe" pe a fesiligia "E i ai sau EEPROM faitau o le BCM e pei ona faia muamua. Filifili "Ioe" pe a fesiligia pe i ai sau EEPROM faitau le ECU e pei ona faia muamua. Filifili le BCM EEPROM Faitau, ona filifili lea o le EERead. A fa'aoso i le "Cycle Key", ki 'ese ona toe fo'i lea i le Run/On pe a fa'aosoina. O le taimi lava e fa'aalia ai le fa'ailoga manuia o le PATs e mafai ona e amataina le ta'avale.
ITULAU 5: 2020-2022 6.7L Powerstroke Transmission Fa'alogo
Laasaga 1: Fa'afeso'ota'i le uaea OBD2 tu'uina atu i le AMDP Powerstroke Programmer ma le uafu OBD2 o le ta'avale. Liliu le ki o le taavale i le tulaga Run/On.
Laasaga 2: Faʻafesoʻotaʻi le AMDP Power Programmer i le komepiuta faʻavae Windows.
Laasaga 3: Tatala le polokalama AutoFlasher, filifili "Cable", ona Filifili "Fesoʻotaʻi". Afai e manuia le fesoʻotaʻiga alu i le Laasaga 4, pe a le toe faʻapipiʻi le USB Drivers ma siaki fesoʻotaʻiga USB.
Laasaga 4: Filifili "OBD", ona "Faailoa". Filifili "TCU" ona "ulufale". Ole TCU S/N ole a amata ile “5”. Fa'amaonia le TCM o lo'o feso'ota'i ma. Afai e leai, siaki feso'ota'iga eletise ma toe fai le Laasaga 3.
Laasaga 5: Filifili "OBD", ona "Maua VIN". Ole Cable S/N, TCU S/N ma le VIN e mana'omia ile imeli ile tunes@dirtydieselcustoms.com ma lau numera oka ma po'o ai na e fa'atonuina e maua ai le fa'atau fa'atau. Ina ia kopi numera ta'itasi kiliki sa'o ona Ctrl-V ile imeli.
Laasaga 6: A uma ona e mauaina fati e ala ile imeli, fa'asaoina i lau komepiuta. Toe fai Laasaga 1-4 pe afai ua motusia le ta'avale.
Laasaga 7: Filifili "OBD", ona "Misc Routines", ona "Clear Tans Adaptive Learn". O le a toe setiina le Transmission KAM (Keep Alive Memory)
Laasaga 8: Filifili le "OBD", ona "Tusi", ona "TCU", filifili le TCM Tune file na imeli muamua atu ia te oe. A mae'a le fa'alogo e tape le ki ona toe fa'aola lea, e mafai ona e motusia uma so'otaga AMDP Powerstroke Programmer.
Laasaga 9: Amata le taʻavale ma faʻamautinoa e leai ni tulafono a le DTC poʻo ni feʻau faʻailoga o loʻo iai. Afai ei ai se mea fa'amolemole fa'afeso'ota'i le lagolago fa'atekinolosi.
ITULAU 6: 2017-2023 6.6L Duramax L5P ECM Tatala
Laasaga 1: Faʻafesoʻotaʻi le AMDP Powerstroke Programmer i le taavale OBD2 port ma le L5P Unlock cable (uaea faʻalautele puʻupuʻu ma uaea moli) ma le OBD2 uaea.
Laasaga 2: Fa'apipi'i le uaea moli i le ECM Fuse. Mo le 17-19 taavale, o le Fuse 57 (15A). Mo le 20+ taavale, o le fuse 78 (15A).
Laasaga 3: Faʻafesoʻotaʻi le AMDP Powerstroke Programmer i le komepiuta faʻavae Windows.
Laasaga 4: Liliu le ki o le Ta'avale i le Ta'avale/O'i tulaga (Aua le amataina le ta'avale).
Laasaga 5: Tatala le polokalama AutoFlasher, Filifili "Cable" ona "Fesoʻotaʻi". Afai e manuia le fesoʻotaʻiga alu i le Laasaga 6, pe a le toe faʻapipiʻi le USB Drivers ma siaki fesoʻotaʻiga USB.
Laasaga 6: Filifili "OBD", "OEM", ona filifili lea "GM". Filifili "OBD", ona "Power On". Filifili "OBD", ona "Faailoa". Kopi ma fa'asaoina le fa'amatalaga o le Bootloader ma le Vaega ua toe maua mai.
Laasaga 7: Filifili "OBD", ona "Power On". Filifili le "OBD", "Tatala", Faʻatino Tatala". Ua tatau nei ona amata le faiga e tatala ai. Afai e talosaga le polokalama e fa'amalo le vaega, filifili ioe ma fa'aofi numera o vaega o lo'o teuina i le Laasaga 6.
Laasaga 8: A maeʻa le Tatala faiga, filifili "OBD", ona "Power Off". Filifili le "Cable", ona "Disconnect". E mafai nei ona e motusia le Polokalama mai le ta'avale ma toe fa'apipi'i le fuse ECM ua aveese i le Laasaga 2.
Laasaga 9: Amata le taavale. Afai e le ola le taavale, fa'amolemole fa'afeso'ota'i le Tech Support. Ua tatala nei le ECM ma ua sauni e fa'aoga e fa'aoga HP Tuners ma se MPVI sa'o i totonu ole OBD Port.
ITULAU 7: Fa'aopoopoina VIN License Credits
Laasaga 1: Faʻafesoʻotaʻi le AMDP Powerstroke Programmer i le komepiuta faʻavae Windows.
Laasaga 2: Tatala le polokalama AutoFlasher.
Laasaga 3: Filifili "Credits", ona "Siaki aitalafu".
Laasaga 4: O Credits e tatau ona otometi ona faaopoopo. Afai e le mautinoa o loʻo e fesoʻotaʻi i le initaneti ma toe fai laasaga 1-3.
Pepa / Punaoa
 |
AMDP AMDP Pule Polokalama [pdf] Taiala mo Tagata Fa'aoga AMDP Polokalame Malosi, Polokalame Malosi, Polokalame |
