IRRADIO Simplified Universal Remote Control with Learning Function

1. Folasaga

This manual provides detailed instructions for the setup, operation, and maintenance of your IRRADIO Simplified Universal Remote Control. This remote is designed for ease of use, featuring a learning function to replicate commands from your original remote control. Its simplified layout and large buttons make it suitable for users of all ages.

2. Oloa Ua Ovaview

The IRRADIO Simplified Universal Remote Control is an infrared remote with a minimalist design. It features essential buttons for common functions, making it straightforward to operate.

Ata 2.1: Luma view of the IRRADIO Simplified Universal Remote Control. It features large, clearly labeled buttons for power, volume, channel, and two programmable auxiliary buttons (A and B).

Galuega Fa'amau:

• Fa'amau o le Malosiaga (Mumu): Ki'i pe tape le masini.
• AV Button (Mute): Toggles audio mute or switches AV input (programmable).
• V+ / V-: Fa'ateleina pe fa'aitiitia le leo.
• P+ / P-: Suia i luga pe i lalo auala.
• A / B Buttons: Two additional programmable buttons for frequently used functions.
• Indicator LED (Red dots): Lights up during button press and programming.

3. Seti: Fa'apipi'i ma'a

The remote control requires 2x AAA/LR03 1.5V batteries (not included).

1. Su'e le vaega o le maa i tua o le masini mamao.
2. Faasolo tatala le ufiufi potu ufiufi.
3. Insert two AAA/LR03 batteries, ensuring the correct polarity (+ and -) as indicated inside the compartment.
4. Tapuni lelei le ufiufi o le vaega o maa.

Fa'aaliga: The remote retains programmed memory even after battery replacement.

4. Operating Instructions: Programming the Remote Control

This universal remote uses a learning function to copy signals from your original remote control. You will need a functional original remote for programming.

Laasaga Polokalama:

1. Sauniuniga: Place the IRRADIO universal remote and your original remote control on a flat surface, facing each other, with their infrared emitters aligned at a distance of approximately 1-3 cm.
2. Ulufale i le Faiga A'oa'oga: Oomi ma uu le Malosiaga faamau ma le AV button simultaneously on the IRRADIO remote for about 3 seconds. The red indicator LED will light up continuously, indicating the remote is in learning mode.
3. Select Button to Program: Press the button on the IRRADIO remote that you wish to program (e.g., V+, P+, A, B). The red indicator LED will start blinking slowly, waiting for a signal.
4. Transmit Signal: Press and hold the corresponding button on your original remote control (e.g., Volume Up, Channel Up). Keep holding it until the IRRADIO remote's LED blinks rapidly three times and then lights up continuously again. This indicates successful learning.
5. Program More Buttons: Repeat steps 3 and 4 for each button you wish to program.
6. Alu Ese Mai le Faiga o le Aoaoina: Once all desired buttons are programmed, press the Malosiaga button on the IRRADIO remote to exit learning mode. The red indicator LED will turn off.

Fa'amatalaga Taua:

• If the LED does not blink rapidly or turns off during programming, the learning process may have failed. Try again, ensuring proper alignment and battery levels in both remotes.
• Ensure the original remote has sufficient battery power for signal transmission.
• The remote can be reprogrammed infinitely.

5. Tausiga

Suiga maa:

When the remote control's response becomes sluggish or the indicator LED does not light up, it is time to replace the batteries. Follow the battery installation steps in Section 3.

Fa'amamaina:

To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or wet cloths, as these can damage the surface or internal components.

6. Faʻafitauli

• Le mamao e le tali mai:
  • Siaki pe ua sa'o le fa'aofiina o maa ma le polarity sa'o.
  • Replace old batteries with new AAA/LR03 batteries.
  • Ia mautinoa e leai ni fa'alavelave i le va o le mamao ma le masini.
• Learning function fails:
  • Ensure the original remote control is working and has sufficient battery power.
  • Verify that the IRRADIO remote and the original remote are aligned correctly, facing each other at a close distance (1-3 cm).
  • Make sure you are pressing and holding the buttons for the required duration during programming.
  • Try programming in a room with less ambient light, as strong light sources can sometimes interfere with IR signals.
• Programmed button does not work:
  • The learning process might not have been successful for that specific button. Repeat the programming steps for that button.
  • Ensure the original remote's signal was strong and clear during programming.

7. Fa'amatalaga

8. Fa'amaonia ma Lagolago

For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official Irradio webnofoaga. Taofi lau fa'amaoniga o le fa'atau mo tagi fa'amaonia.