Tusitaiala mo le Tagata Fa'aoga o le Ecolink WST-232 Wireless Home Security Door Window Sensor

Folasaga

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ecolink WST-232 Wireless Home Security Door Window Sensor. This device is designed to enhance the security of your home by detecting the opening and closing of doors and windows. It is compatible with Honeywell 5800 Wireless and 2GIG security systems.

Fa'amatalaga Taua mo le Saogalemu

• Faitau fa'atonuga uma ma le fa'aeteete a'o le'i fa'apipi'i ma fa'aoga.
• Do not attempt to repair or modify the sensor. Refer all servicing to qualified personnel.
• Keep batteries out of reach of children. Dispose of used batteries properly according to local regulations.
• Ensure the sensor is installed in a location where it will not be exposed to extreme temperatures or moisture.

O mea o lo'o i totonu

Fa'amautinoa o lo'o iai mea uma i totonu o le afifi:

• Ecolink WST-232 Wireless Door/Window Sensor (Main Unit)
• Magnet (for contact detection)
• Meafaigaluega Fa'apipi'i (sikulimi, lipine fa'apipi'i)
• Interchangeable Brown Case
• Tusi Lesona a le Tagata (lenei pepa)

Ua Umaview

The Ecolink WST-232 is a compact wireless sensor designed for monitoring the open/closed status of doors and windows. It features an internal reed switch for standard magnetic contact detection and an external contact input for connecting wired devices.

Ata: Ecolink WST-232 Wireless Door/Window Sensor showing the main unit and the external contact wires.

Vaega Autu:

• Iunite Autu o le Sensor: Contains the battery, wireless transmitter, and internal reed switch.
• Maneta: Triggers the internal reed switch when separated from the main unit.
• External Contact Input: Two wires (typically red and black) for connecting an external wired contact.
• Vaega ma'a: Located on the back of the main unit.

Seti ma Fa'apipi'i

1. Fa'apipi'i ma'a

1. Tatala le masini fa'alogo casing by gently prying it open from the side notch.
2. Insert the CR2032 lithium battery, ensuring the positive (+) side faces up.
3. Tapuni le masini casing saogalemu.

2. Enrolling the Sensor with Your Security Panel

The WST-232 sensor is compatible with Honeywell 5800 Wireless and 2GIG security systems. Refer to your security panel's manual for specific enrollment procedures. General steps are as follows:

1. Put your security panel into programming mode for adding new wireless zones.
2. Activate the sensor by separating the magnet from the main unit, or by connecting/disconnecting the external contact wires. This sends a signal to the panel.
3. Confirm the sensor's serial number is learned by the panel.
4. Assign the sensor to an appropriate zone type (e.g., "Entry/Exit," "Perimeter").
5. Exit programming mode on your panel.

3. Fa'amauina le Sensor

Choose a suitable location on your door or window frame. The sensor and magnet should be mounted within 0.5 inches (1.27 cm) of each other when the door/window is closed.

Ata: Ecolink WST-232 sensor components including the main unit, magnet, and mounting screws.

Fa'aaogā Screws:

1. Position the main sensor unit on the stationary frame and the magnet on the moving part (door/window).
2. Faailoga pu sikulima.
3. vili pu pailate pe a mana'omia.
4. Secure both the sensor and magnet with the provided screws.

Using Adhesive Tape (not recommended for long-term security):

1. Clean the mounting surfaces thoroughly.
2. Apply adhesive tape to the back of the sensor and magnet.
3. Press firmly onto the desired surfaces for at least 30 seconds.

4. External Contact Input

The WST-232 includes an external contact input for integrating other wired devices, such as recessed door contacts or pressure mats. Connect the two wires from your external device to the red and black wires of the WST-232 sensor. The sensor will transmit a signal when the external contact opens or closes.

Fa'agaoioia o le Sensor

Once installed and enrolled, the Ecolink WST-232 sensor operates automatically. When the door or window it is monitoring opens, separating the magnet from the main unit (or opening the external contact), the sensor will transmit a signal to your security panel. This signal indicates an "open" state. When the door or window closes, bringing the magnet back into proximity (or closing the external contact), the sensor transmits a "closed" state signal.

Your security panel will then react according to its programming (e.g., trigger an alarm if the system is armed, log the event).

Tausiga

Suiga maa

The sensor uses one CR2032 lithium battery. When the battery level is low, your security panel will typically display a low battery warning for the corresponding zone. To replace the battery:

1. Put your security panel into disarm or test mode to prevent false alarms.
2. Tatala mālie le sensor casing.
3. Aveese le maa tuai CR2032.
4. Fa'aofi se maa fou CR2032, ia mautinoa o le polarity sa'o (+ itu i luga).
5. Tapuni le masini casing saogalemu.
6. Test the sensor to ensure it communicates with the panel.

Fa'amamaina

Clean the sensor and magnet with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.

Fa'afitauli

Fa'amatalaga

• Fa'ata'ita'iga: WST-232
• Fegalegaleai: Honeywell 5800 Wireless, 2GIG
• itu: 3 x 1.7 x 1 inisi (fa'atatau)
• ma'a: 1 x CR2032 Lithium Coin Cell
• Fa'agaoioi Auala: 345 MHz
• Tufuga: Ecolink Intelligent Technology Inc
• UPC: 657479755391

Fa'amaonia ma Lagolago Fa'ainisinia

For warranty information and technical assistance, please refer to the official Ecolink web'upega tafaʻilagi pe faʻafesoʻotaʻi saʻo la latou tautua faʻatau. Taofi lau lisiti faʻatau e fai ma faʻamaoniga o le faʻatau.

Ecolink Webnofoaga: www.ecolink.com