KeylessOption EZSDEI7141 474V

KeylessOption Keyless Entry Remote Starter Car Key Fob User Manual

Model: EZSDEI7141 474V

Folasaga

This manual provides comprehensive instructions for the KeylessOption Keyless Entry Remote Starter Car Key Fob. This remote is designed as a replacement for aftermarket Viper alarm and remote start systems. Ensure your original remote's FCC ID matches EZSDEI7141 for compatibility.

Luma view of the KeylessOption Key Fob with lock, unlock, AUX, and star buttons.

Ata: Luma view of the KeylessOption Key Fob, displaying the lock, unlock, AUX, and star buttons.

Seti ma Polokalama

Programming this remote requires locating the Viper system's control button, often found near the rearview mirror, under the dashboard, or in other discreet locations depending on the installation. Refer to your vehicle's specific Viper system manual or consult a professional if you cannot locate it.

Laasaga Polokalama:

  1. Open the driver's side door of your vehicle.
  2. Insert the key into the ignition and turn it to the ON position. Do not start the engine.
  3. Locate the Viper system's control button (often a small button with a blue LED indicator).
  4. Oomi le faamau pule faafitu. I luga o le eighth press, hold the button down until the car chirps.
  5. While still holding the control button, press the Loka button on your new KeylessOption remote. The car should chirp again to confirm successful programming.
  6. Faʻamatuʻu le faʻamau faʻatonutonu.
  7. Liliu le ki mu i le TOTO tulaga ma aveese.
  8. Tapuni le faitotoʻa i le itu o le avetaavale.
  9. Test the remote's functions (Lock, Unlock, etc.) to ensure proper operation.

If you are programming multiple remotes, repeat steps 4 and 5 for each additional remote before turning the key off in step 6.

Vitio: Ua mae'a se pu'upu'uview of KeylessOption Key Fob Remotes for Viper systems.

Fa'atonuga o Galuega

Once programmed, your KeylessOption remote provides convenient control over your vehicle's aftermarket alarm and remote start system. The remote features four distinct buttons:

  • Loka faamau: Press to lock your vehicle's doors and arm the alarm system.
  • Tatala faamau: Press to unlock your vehicle's doors and disarm the alarm system.
  • AUX button: This button typically controls auxiliary functions, such as opening the trunk or activating a remote start feature, depending on your Viper system's configuration. Refer to your Viper system's manual for specific AUX button functionality.
  • Panic Button (*): Press and hold this button to activate the vehicle's panic alarm. Press again to deactivate.
Fa'afagoto view of the KeylessOption Key Fob, showing the side profile and button layout.

Ata: Fa'afago view of the KeylessOption Key Fob, highlighting its ergonomic design.

Tausiga

Suiga maa:

If your remote's range decreases or it stops responding, the battery may need replacement. The KeylessOption remote uses a standard coin cell battery (e.g., CR2032, check inside the remote for exact type). To replace:

  1. Carefully separate the two halves of the remote casing using a small flat-head screwdriver or a prying tool.
  2. Remove the old battery. Note its orientation (+/- sides).
  3. Insert the new battery with the correct orientation.
  4. Snap the remote casing back together securely.
Tua view of the KeylessOption Key Fob, showing the smooth casing.

Ata: Tua view of the KeylessOption Key Fob, indicating where the casing can be opened for battery access.

Fa'afitauli

  • Le mamao e le tali mai: Ensure the battery is fresh and correctly installed. Re-attempt the programming steps carefully. Verify the FCC ID on your original remote matches EZSDEI7141.
  • Fa'atapula'a va'aiga: Replace the battery. Ensure there are no obstructions between the remote and the vehicle's antenna.
  • Vehicle not chirping during programming: Double-check that the ignition is in the ON position (not ACC or START). Confirm you are pressing the Viper control button the correct number of times and holding it on the last press until a chirp is heard.

Fa'amatalaga

Fa'ailogaKeylessOption
Numera Fa'ata'ita'iEZSDEI7141 474V
Masini FegalegaleaiViper Aftermarket Alarm System
FCC IDEZSDEI7141
Numera o Ki4 (Lock, Unlock, Aux, Panic)
Mea mamafa0.634 aunese
Fuafuaga Mea6.77 x 4.65 x 0.47 inisi

Fa'amaonia ma Lagolago

Each KeylessOption remote includes a warranty card. KeylessOption is an automotive remote company dedicated to providing reliable replacement automotive products. For further assistance or warranty claims, please refer to the contact information provided on your warranty card or visit the official KeylessOption webnofoaga.

KeylessOption Warranty Card

Image: KeylessOption Warranty Card, included with each purchase.

© 2025 KeylessOption. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.